Kyocera FS-C8500DN
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
150000
Скорость печати
A4
55
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Цветность печати |
цветная |
Размещение |
настольный |
Тип устройства |
Принтер |
Макс. формат |
A3 |
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Телефон |
|
Факс |
|
Печать фотографий |
|
Сканер |
|
Копир |
|
Число страниц в месяц |
150 000 |
Область применения |
большой офис |
Принтер |
|
Время разогрева |
57,5 |
Двусторонняя печать |
|
Прямая печать |
|
Пигментные чернила |
|
Печать без полей |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 600 |
| По Y | 600 |
Скорость ч/б печати |
|
| A3 | 50 |
| A4 | 55 |
| A3 | 25 |
Скорость цветной печати |
|
| A4 | 28 |
Время выхода первого отпечатка |
|
| Цветн, | 6,7 |
| Ч/б | 5,2 |
Сканер |
|
Стандарт WIA |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
15 000 |
Ресурс цветного картриджа/тонера |
7 000 |
Количество картриджей |
4 |
Печать на: |
|
| CD/DVD |
|
| Фотобумаге |
|
| Рулоне |
|
| Карточках |
|
| Глянцевой бумаге |
|
| Конвертах |
|
| Матовой бумаге |
|
| Этикетках |
|
| Пленках |
|
Плотность бумаги |
|
| Максимальная | 220 |
| Минимальная | 60 |
Факс |
|
PC Fax |
|
Цветной |
|
Телефон |
|
АОН |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Проводная трубка |
|
Беспроводная трубка |
|
Caller ID |
|
Языки управления |
|
| PCL 6 |
|
|
|
|
| PostScript |
|
| PostScript 3 |
|
| PCL 5c |
|
| PCL 5e |
|
| PPDS |
|
| PostScript 2 |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 1 100 |
| Максимальная | 4 100 |
Вывод бумаги |
|
| Стандартный | 500 |
Финишер |
|
Электронная сортировка |
|
Степлер |
|
Сортировка со сдвигом |
|
Сортер |
|
Брошюровщик |
|
Интерфейсы |
|
Количество свободных слотов расширения |
1 |
Версия USB |
2,0 |
Устройство для чтения карт памяти |
|
Веб-интерфейс |
|
Ethernet (RJ-45) |
|
USB |
|
Bluetooth |
|
Инфракрасный порт |
|
RS-232 |
|
Wi-Fi |
|
LPT |
|
FireWire (IEEE 1394) |
|
Поддержка карт памяти |
|
| CompactFlash |
|
Память/Процессор |
|
Частота процессора |
750 |
Процессор |
PowerPC 750GL |
Объем памяти |
1 024 |
Макс, объем памяти |
2 048 |
Дополнительная информация |
|
Мин. системные требования |
Intel Pentium III |
Работа от аккумулятора |
|
Поддержка ОС |
|
| Windows |
|
| Linux |
|
| Mac OS |
|
| DOS |
|
Потребляемая мощность |
|
| При работе | 1 270 |
| В режиме ожидания | 200 |
Уровень шума |
|
| При работе | 55 |
| В режиме ожидания | 26 |
Габариты |
|
Глубина |
691 |
Высота |
680 |
Ширина |
605 |
Вес |
99 |
Модули
Covers 1
Covers 2
Paper Feed Section 1
ELECTRICAL COMPONENTS 2
DRIVE SECTION 4
Retainer Section-2
DRIVE SECTION 2
COOLING SECTION
Paper Cassette 1
FRAMES 1
Paper Feed Section 3
Paper Conveying Section 2-2
Options 1
Paper Conveying Section 2-3
Paper Conveying Section 1
Electrical Components 3
Fuser Section
FRAMES 2
Drive Section 1
TRANSFER SECTION
Exit Section
DEVELOPING SECTION
DRIVE SECTION 3
Options 2
Paper Conveying Section 2-1
Paper Feed Section 4
Retainer Section-1
PAPER FEED SECTION 2
Laser Scanner Section
Image Formation Section
Electrical Components 1
Paper Cassette 2
Детали Drive Section 1
| Деталь: | STOPPER PAPER |
| Парткод: | 302KA04090 |
| Деталь: | COVER TOP |
| Парткод: | 302KA04011 |
| Деталь: | LABEL CONVEY JAM |
| Парткод: | 302KA34030 |
| Деталь: | COVER LEFT RT |
| Парткод: | 302H704141 |
| Деталь: | COVER LEFT FRONT TOP |
| Парткод: | 302H704361 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302FZ04240 |
| Деталь: | COVER LEFT RL |
| Парткод: | 302H704130 |
| Деталь: | SPRING FEED LOW |
| Парткод: | 302H704870 |
| Деталь: | LOCK COVER R /40283V0068 A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | COVER LEFT FRONT |
| Парткод: | 302FZ04150 |
| Деталь: | PIN FRONT COVER |
| Парткод: | 302H704540 |
| Деталь: | COVER FRONT LEFT INN |
| Парткод: | 302H704390 |
| Деталь: | COVER FRONT LEFT MID |
| Парткод: | 302H704070 |
| Деталь: | SPRING COVER FL |
| Парткод: | 302H704400 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | SHAFT FEED B |
| Парткод: | 302BG06152 |
| Деталь: | PULLEY FEED |
| Парткод: | 302KY22010 |
| Деталь: | COVER LEFT FEED LOW |
| Парткод: | 302H704660 |
| Деталь: | BUSH SP B |
| Парткод: | 302H722730 |
| Деталь: | SPRING FEED LOW B |
| Парткод: | 302H722740 |
| Деталь: | GUIDE LEFT FEED LOW |
| Парткод: | 302H722810 |
| Деталь: | HANDLE LEFT FEED COVER |
| Парткод: | 303LM04080 |
| Деталь: | COVER FILTER DUCT PU |
| Парткод: | 302H733250 |
| Деталь: | FILTER DUCT PU KME |
| Парткод: | 302H733630 |
| Деталь: | COVER FRONT LEFT |
| Парткод: | 302H704060 |
| Деталь: | COVER INNER RIGHT |
| Парткод: | 302H704630 |
| Деталь: | SEAL FAN RETAINER 1 |
| Парткод: | 302H704830 |
| Деталь: | SEAL FAN RETAINER 2 |
| Парткод: | 302H704840 |
| Деталь: | CS EMBLEM SHEET |
| Парткод: | 302H734250 |
| Деталь: | COVER REAR TOP |
| Парткод: | 302KA04041 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | 302G634070 |
| Деталь: | PARTS COVER FRONT ASSY SP |
| Парткод: | 302KA94170 |
| Деталь: | PARTS EMBLEM ASSY E SP |
| Парткод: | 302KA94120 |
| Деталь: | COVER RIGHT TOP |
| Парткод: | 302KA04050 |
| Деталь: | COVER RIGHT |
| Парткод: | 302KY04051 |
| Деталь: | SPONGE RIGHT FAN D |
| Парткод: | 302KY04040 |
| Деталь: | SPONGE RIGHT FAN B |
| Парткод: | 302H704810 |
| Деталь: | SPONGE RIGHT FAN C |
| Парткод: | 302H704820 |
| Деталь: | COVER FILTER VU |
| Парткод: | 302H733080 |
| Деталь: | FILTER VU |
| Парткод: | 302H733170 |
| Деталь: | COVER MAIN SW |
| Парткод: | 302H704170 |
| Деталь: | FILTER VOC |
| Парткод: | 302H733610 |
| Деталь: | GUIDE FILTER VOC |
| Парткод: | 302H733600 |
| Деталь: | EARTH PUSH SWITCH |
| Парткод: | 302HP04140 |
| Деталь: | COVER EXIT |
| Парткод: | 302HP04080 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | SHEET COVER EXIT |
| Парткод: | 302KA04110 |
| Деталь: | COVER LEFT FRONT |
| Парткод: | 302KA04030 |
| Деталь: | COVER FILTER RIGHT |
| Парткод: | 302KY04020 |
| Деталь: | FILTER FAN RIGHT |
| Парткод: | 302KY04030 |
| Деталь: | SEAL COVER REAR B |
| Парткод: | 302H704580 |
| Деталь: | COVER LOWER REAR |
| Парткод: | 302H704230 |
| Деталь: | COVER REAR |
| Парткод: | 302KA04020 |
| Деталь: | LID KMAS |
| Парткод: | 2C912430 |
| Деталь: | GUIDE COVER FILTER |
| Парткод: | 302H733420 |
| Деталь: | COVER FILTER |
| Парткод: | 302H733400 |
| Деталь: | FILTER COOLING FAN |
| Парткод: | 302H733410 |
| Деталь: | LID COVER RIGHT |
| Парткод: | 302H704040 |
| Деталь: | SEAL COVER REAR A |
| Парткод: | 302H704570 |
| Деталь: | TAPE PANEL |
| Парткод: | 302F805130 |
| Деталь: | SHEET LED |
| Парткод: | 302J005100 |
| Деталь: | COVER OPERATION |
| Парткод: | 302KA05010 |
| Деталь: | BUTTON ENTER |
| Парткод: | 302KA05020 |
| Деталь: | BUTTON COMBI |
| Парткод: | 302KA05030 |
| Деталь: | LENS LED |
| Парткод: | 302KA05040 |
| Деталь: | BUTTON STOP |
| Парткод: | 302KA05050 |
| Деталь: | HOLDER PWB |
| Парткод: | 302KA05060 |
| Деталь: | PLATE LCD |
| Парткод: | 302KA05070 |
| Деталь: | WIRE PANEL |
| Парткод: | 302KA46070 |
| Деталь: | PARTS PWB PANEL ASSY SP |
| Парткод: | 302KA94040 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SHEET STATIC LCD |
| Парткод: | 302H905390 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTGR55060H01 |
| Деталь: | WIRE USB HOST |
| Парткод: | 302KA46100 |
| Деталь: | WIRE PANEL JOINT |
| Парткод: | 302KA46060 |
| Деталь: | GUIDE WIRE F |
| Парткод: | 302KA02070 |
| Деталь: | LABEL MP CAUTION |
| Парткод: | 302H734290 |
| Деталь: | LABEL CAUTION HG |
| Парткод: | 302H734030 |
| Деталь: | SPRING USB HOST |
| Парткод: | 302H005661 |
| Деталь: | HOLDER USB |
| Парткод: | 302KA05080 |
| Деталь: | LABEL LED SHEET |
| Парткод: | 302J005140 |
| Деталь: | PARTS FILTER VU ASSY |
| Парткод: | 302H794430 |
| Деталь: | PARTS FILTER RIGHT UNIT SP |
| Парткод: | 302KY94160 |
| Деталь: | PARTS COVER FILTER UNIT |
| Парткод: | 302H794630 |
| Деталь: | PARTS OPERATION UNIT (E A) SP |
| Парткод: | 302KA94090 |
| Деталь: | PULLEY, PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | GUIDE FILM,SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | SHAFT,PAPER FEED |
| Парткод: | 302AR07252 |
| Цена: | 420 ₽ |
| Деталь: | SHAFT,LEADING FEED |
| Парткод: | 302AR07271 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 302FG07253 |
| Деталь: | LOWER HOUSING, PAPER FEED |
| Парткод: | 302FG07260 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 302FG07290 |
| Деталь: | HOLDER,ACTUATOR |
| Парткод: | 302FG07300 |
| Деталь: | REINFORCEMENT PRIMARY PAPER FEED |
| Парткод: | 302FG07310 |
| Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
| Парткод: | 302FG07330 |
| Деталь: | HOLDER PICK |
| Парткод: | 302GR06060 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 302GR06070 |
| Деталь: | SPRING PICK |
| Парткод: | 302GR06080 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 302GR06091 |
| Деталь: | SHAFT SEPARATION |
| Парткод: | 302GR06101 |
| Деталь: | TORQUE LIMITER 360 |
| Парткод: | 302GR06110 |
| Деталь: | LEVER SEPARATION RELEASE |
| Парткод: | 302GR06201 |
| Деталь: | WIRE PRIMARY FEED UNIT1 |
| Парткод: | 302GR46431 |
| Деталь: | COVER PRIMARY WIRE |
| Парткод: | 302H706010 |
| Деталь: | GEAR Z16 PAPER FEED |
| Парткод: | 302KY06010 |
| Деталь: | LOWER BUSHING, PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PARTS PRYMARY FEED UNIT SP |
| Парткод: | 302KY94250 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302KA94031 |
| Деталь: | WIRE CONTAIN MOT JOINT |
| Парткод: | 302H746170 |
| Деталь: | SHEET PWB |
| Парткод: | 302H739900 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | MOUNT HV TERMINAL |
| Парткод: | 302FZ39110 |
| Деталь: | SPRING HV MAIN |
| Парткод: | 302FZ39520 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN |
| Парткод: | 302H794360 |
| Деталь: | SPRING HV TC1 |
| Парткод: | 302H739540 |
| Деталь: | COVER HV TC1 |
| Парткод: | 302H739590 |
| Деталь: | MOUNT TRANSFER HV 2 |
| Парткод: | 302H739600 |
| Деталь: | TERMINAL TC1 2 |
| Парткод: | 302H739610 |
| Деталь: | SHEET TC1 |
| Парткод: | 302H739620 |
| Деталь: | WIRE HVU T1 |
| Парткод: | 302H746360 |
| Деталь: | PARTS UNIT HIGH VOLTAGE TRANSFER1 |
| Парткод: | 302H794370 |
| Деталь: | GUIDE WIRE MAIN |
| Парткод: | 302H702530 |
| Деталь: | MOUNT CONT BOX |
| Парткод: | 302H702120 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | GUIDE WIRE EXIT |
| Парткод: | 302H739220 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610005++H01 |
| Деталь: | WIRE RIGHT SIDE |
| Парткод: | 302KA46090 |
| Деталь: | PLATE INLET |
| Парткод: | 302H739050 |
| Деталь: | WIRE INLET ASSY |
| Парткод: | 302H746420 |
| Деталь: | WIRE MSW US |
| Парткод: | 302KA46170 |
| Деталь: | WIRE MSW |
| Парткод: | 302KA46130 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC020201+++H01 |
| Деталь: | WIRE TRANSFER-EXIT |
| Парткод: | 302KA46030 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | GUIDE WIRE L |
| Парткод: | 302H739160 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE FEED |
| Парткод: | 302H746340 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | SHEET PS |
| Парткод: | 302H702190 |
| Деталь: | BRACKET OPTION IF |
| Парткод: | 302H739070 |
| Деталь: | BRACKET LVU PWB |
| Парткод: | 302H739080 |
| Деталь: | GUIDE WIRE LVU |
| Парткод: | 302H739280 |
| Деталь: | GUIDE WIRE HV |
| Парткод: | 302H739300 |
| Деталь: | SHEET OPTION IF |
| Парткод: | 302H739340 |
| Деталь: | SHEET OPTION CV |
| Парткод: | 302H739350 |
| Деталь: | PARTS UNIT LOW VOLTAGE |
| Парткод: | 302H794351 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | SPACER,KGPS-4S |
| Парткод: | M2108130 |
| Деталь: | WIRE LVU |
| Парткод: | 302KA46080 |
| Деталь: | WIRE OP DESK |
| Парткод: | 302KA46140 |
| Деталь: | WIRE MAIN-ENGINE |
| Парткод: | 302H746390 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H739270 |
| Деталь: | WIRE OP HEATER RELAY |
| Парткод: | 302KA46150 |
| Деталь: | WIRE SOLENOID 2 |
| Парткод: | 302KA46050 |
| Деталь: | SHEET FRAME FUSER R |
| Парткод: | 302KA02090 |
| Деталь: | WIRE JUMPER CONNECTOR |
| Парткод: | 302H746A00 |
| Деталь: | CLAMP,LCT-1.5SIEM(TAKEUCHI) |
| Парткод: | M70AF010 |
| Деталь: | WIRE OP HEATER SW |
| Парткод: | 302H746990 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | PIN MAIN DRIVE |
| Парткод: | 302FZ31720 |
| Деталь: | PIN EXIT |
| Парткод: | 302FZ31750 |
| Деталь: | SPRING EXIT 60 |
| Парткод: | 302FZ31790 |
| Деталь: | PARTS,FAN COOLING DLP 70 SP |
| Парткод: | 302FZ94380 |
| Деталь: | HOLDER CONT DRIVE |
| Парткод: | 302H731511 |
| Деталь: | PLATE CONT DRIVE |
| Парткод: | 302H731520 |
| Деталь: | GEAR Z61L Z21 CONT D |
| Парткод: | 302H731530 |
| Деталь: | GEAR Z49 P26 CONT D |
| Парткод: | 302H731540 |
| Деталь: | GEAR Z55 CONT D |
| Парткод: | 302H731550 |
| Деталь: | GEAR Z34L Z22R |
| Парткод: | 302H731561 |
| Деталь: | GEAR Z39 CONT D |
| Парткод: | 302H731570 |
| Деталь: | GEAR Z34L Z22L CONT D |
| Парткод: | 302H731581 |
| Деталь: | PULLEY 32 CONT D |
| Парткод: | 302H731590 |
| Деталь: | PIN CONT D |
| Парткод: | 302H731600 |
| Деталь: | SHAFT PADDLE CONT D |
| Парткод: | 302H731610 |
| Деталь: | DUCT CONT D |
| Парткод: | 302H731620 |
| Деталь: | COVER DUCT CONT D |
| Парткод: | 302H731630 |
| Деталь: | COUPLING CONT D |
| Парткод: | 302H731640 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | SPRING SPIRAL CONT D |
| Парткод: | 302H731660 |
| Деталь: | HOLDER SPIRAL DRIVE H |
| Парткод: | 302H731690 |
| Деталь: | GEAR Z21 CONT |
| Парткод: | 302H731700 |
| Деталь: | WORM WHEEL 22-Z14 |
| Парткод: | 302H731710 |
| Деталь: | BELT CONT D |
| Парткод: | 302H731760 |
| Деталь: | GEAR Z34 CONT D |
| Парткод: | 302H731780 |
| Деталь: | GERA Z46L CONT D |
| Парткод: | 302H731790 |
| Деталь: | GEAR Z38L CONT D |
| Парткод: | 302H731930 |
| Деталь: | HOLDER JOINT CNG |
| Парткод: | 302H731951 |
| Деталь: | GEAR Z28R JOINT |
| Парткод: | 302H731971 |
| Деталь: | SHAFT OWCE CONT D |
| Парткод: | 302H732030 |
| Деталь: | GEAR Z61L OW |
| Парткод: | 302H732040 |
| Деталь: | GEAR Z34L CONT D |
| Парткод: | 302H732050 |
| Деталь: | GEAR Z34R Z22R CONT D |
| Парткод: | 302H732070 |
| Деталь: | SHEET WIRE CONT D |
| Парткод: | 302H732170 |
| Деталь: | PLATE EARTH CONT D |
| Парткод: | 302H732180 |
| Деталь: | CASE FAN CONT D |
| Парткод: | 302H732200 |
| Деталь: | COLLAR PULLEY CONT D |
| Парткод: | 302H732210 |
| Деталь: | WIRE CONTAIN MOT |
| Парткод: | 302H746180 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302H794170 |
| Деталь: | PARTS DC MOTOR ASSY |
| Парткод: | 302H794440 |
| Деталь: | PARTS FAN COOLING FRONT |
| Парткод: | 302H794710 |
| Деталь: | PARTS MOTOR CLN SP |
| Парткод: | 302KY94110 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | GEAR WORM /48390M0062 A4 |
| Парткод: | 5MVG115DB002 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS CONT DRIVE UNIT A SP |
| Парткод: | 302KY94180 |
| Деталь: | PARTS CONT DRIVE UNIT E SP |
| Парткод: | 302KY94190 |
| Деталь: | PARTS CONT DRIVE UNIT AO SP |
| Парткод: | 302KY94320 |
| Деталь: | LABEL PUSH A |
| Парткод: | 302H734170 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | GEAR SWEEP Z23 |
| Парткод: | 302FZ02830 |
| Деталь: | GEAR MPT Z23 |
| Парткод: | 302FZ08180 |
| Деталь: | SHAFT DRIVE A |
| Парткод: | 302H702600 |
| Деталь: | SHAFT DRIVE B |
| Парткод: | 302H702610 |
| Деталь: | BUSH COUPLING |
| Парткод: | 302H702620 |
| Деталь: | BUSH JOINT |
| Парткод: | 302H702640 |
| Деталь: | PLATE WASTE DRIVE |
| Парткод: | 302H702650 |
| Деталь: | SHAFT DRIVE C |
| Парткод: | 302H702680 |
| Деталь: | TORQUE LIMITER |
| Парткод: | 302H702690 |
| Деталь: | GEAR JOINT Z20S |
| Парткод: | 302H702700 |
| Деталь: | GEAR WASTE Z12S |
| Парткод: | 302H702710 |
| Деталь: | GEAR WASTE Z25 Z24 |
| Парткод: | 302H702720 |
| Деталь: | GEAR WASTE Z24S |
| Парткод: | 302H702730 |
| Деталь: | HOLDER DRIVE A |
| Парткод: | 302H702740 |
| Деталь: | HOLDER JOINT JV |
| Парткод: | 302H702780 |
| Деталь: | COUPLING WASTE |
| Парткод: | 302H702800 |
| Деталь: | HOLDER DRIVE C |
| Парткод: | 302H702990 |
| Деталь: | TRAY WASTE |
| Парткод: | 302H703380 |
| Деталь: | LEVER WASTE TRAY |
| Парткод: | 302H703390 |
| Деталь: | PARTS WASTE BOTTLE UNIT |
| Парткод: | 302KA93040 |
| Деталь: | PARTS MOTOR IMAGE SP |
| Парткод: | 302KY94060 |
| Деталь: | PLATE DRIVE TC |
| Парткод: | 302JD31110 |
| Деталь: | GEAR Z72L Z30L TC |
| Парткод: | 302JD31240 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | SHAFT BYPASS DRIVE |
| Парткод: | 302FZ31221 |
| Деталь: | GEAR Z38R MPF |
| Парткод: | 302FZ31300 |
| Деталь: | GEAR Z26L BYPASS |
| Парткод: | 302FZ31540 |
| Деталь: | GEAR Z27S BYPASS |
| Парткод: | 302FZ31550 |
| Деталь: | PIN MPF DRIVE |
| Парткод: | 302FZ31710 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | PIN CONT D |
| Парткод: | 302H731600 |
| Деталь: | PLATE MPF DRIVE |
| Парткод: | 302H731821 |
| Деталь: | HOLDER MPF DRIVE |
| Парткод: | 302H731831 |
| Деталь: | GEAR Z86L Z30L MPF |
| Парткод: | 302H731840 |
| Деталь: | GEAR Z51L |
| Парткод: | 302H731850 |
| Деталь: | GEAR Z64R |
| Парткод: | 302H731860 |
| Деталь: | GEAR Z21R BRS |
| Парткод: | 302H731871 |
| Деталь: | GEAR Z85L-Z47R MPF |
| Парткод: | 302H731890 |
| Деталь: | SHAFT MPF CL |
| Парткод: | 302H731920 |
| Деталь: | GEAR Z18S BRS |
| Парткод: | 302H732092 |
| Деталь: | PARTS CLUTCH MPF 6 |
| Парткод: | 302H794300 |
| Деталь: | SHAFT BRS DRIVE |
| Парткод: | 302KY31080 |
| Деталь: | PARTS MOTOR MPF SP |
| Парткод: | 302KY94080 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | CUT WASHER |
| Парткод: | 5MVS665KB001 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BEARING, DRIVE |
| Парткод: | 68822330 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS CLUTCH FEED 25 |
| Парткод: | 302H794250 |
| Деталь: | WIRE FEED CLT |
| Парткод: | 302H746520 |
| Деталь: | SHEET STOPPER CLUTCH |
| Парткод: | 302H702550 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | JOINT GEAR EXIT |
| Парткод: | 302FZ31671 |
| Деталь: | PULLEY EXIT DRIVE |
| Парткод: | 302FZ31680 |
| Деталь: | PIN EXIT |
| Парткод: | 302FZ31750 |
| Деталь: | GEAR EXIT Z30 JOINT |
| Парткод: | 302FZ31770 |
| Деталь: | SPRING EXIT 60 |
| Парткод: | 302FZ31790 |
| Деталь: | GEAR Z20 FUSER |
| Парткод: | 302FZ31870 |
| Деталь: | GEAR Z65-Z29 FUSER |
| Парткод: | 302KA31060 |
| Деталь: | PLATE FUSER DRIVE |
| Парткод: | 302FZ32012 |
| Деталь: | HOLDER FUSER CL |
| Парткод: | 302FZ32024 |
| Деталь: | SHAFT FUSER DRIVE |
| Парткод: | 302FZ32031 |
| Деталь: | CLUTCH FUSER 8 |
| Парткод: | 302FZ32043 |
| Деталь: | COVER FUSER MOTOR |
| Парткод: | 302H732010 |
| Деталь: | MOUNT FUSER DRIVE |
| Парткод: | 302H732240 |
| Деталь: | GEAR Z20L FUSER DRIVE |
| Парткод: | 302KA31010 |
| Деталь: | GEAR Z46 FUSER |
| Парткод: | 302KA31020 |
| Деталь: | GEAR EXIT Z48 |
| Парткод: | 302KA31030 |
| Деталь: | GEAR EXIT Z45Z22 |
| Парткод: | 302KA31040 |
| Деталь: | GEAR Z30 FUSER |
| Парткод: | 302KA31050 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 302KY31050 |
| Деталь: | GEAR EXIT Z63 Z21 |
| Парткод: | 302KY31060 |
| Деталь: | GEAR EXIT Z39Z26 |
| Парткод: | 302KY31070 |
| Деталь: | PARTS MOTOR FUSER SP |
| Парткод: | 302KY94120 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | GEAR Z45R REG |
| Парткод: | 302H731290 |
| Деталь: | STOPPER CLUTCH FEED |
| Парткод: | 302H702520 |
| Деталь: | WIRE TRANS MOT JOINT |
| Парткод: | 302KA46120 |
| Деталь: | PARTS MPF DRIVE H UNIT SP |
| Парткод: | 302KY94220 |
| Деталь: | PARTS FUSER DRIVE UNIT |
| Парткод: | 302KY93100 |
| Деталь: | SEAL FAN FRONT |
| Парткод: | 302H733780 |
| Деталь: | FAN 60 COOLING |
| Парткод: | 2FB27190 |
| Деталь: | SCREW FAN |
| Парткод: | 302H733430 |
| Деталь: | LID GUIDE WIRE C |
| Парткод: | 302H017230 |
| Деталь: | DUCT FAN VU UPPER |
| Парткод: | 302H733090 |
| Деталь: | DUCT FAN VU LOWER |
| Парткод: | 302H733100 |
| Деталь: | SHEET STOPPER WIRE VU |
| Парткод: | 302H733220 |
| Деталь: | SHEET FAN VU |
| Парткод: | 302H733590 |
| Деталь: | WIRE FAN LVU |
| Парткод: | 302H746970 |
| Деталь: | SHEET FUN GUIDE |
| Парткод: | 302H733530 |
| Деталь: | DUCT FAN PS2 |
| Парткод: | 302H733210 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | DUCT FAN PS |
| Парткод: | 302H733181 |
| Деталь: | MOUNT FAN IMAGE |
| Парткод: | 302H733110 |
| Деталь: | PARTS FAN IMAGE |
| Парткод: | 302H794700 |
| Деталь: | DUCT FAN FRONT |
| Парткод: | 302H733191 |
| Деталь: | PARTS FAN COOLING FRONT |
| Парткод: | 302H794710 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | PARTS,FAN IMAGE SP |
| Парткод: | 302FZ94660 |
| Деталь: | MOUNT FAN CONT BK |
| Парткод: | 302H733131 |
| Деталь: | COVER FAN CONT BK |
| Парткод: | 302H733140 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS,FAN COOLING DLP 70 SP |
| Парткод: | 302FZ94380 |
| Деталь: | DUCT COOLING FAN |
| Парткод: | 302H733390 |
| Деталь: | DUCT EXIT LOWER |
| Парткод: | 302H733010 |
| Деталь: | DUCT EXIT UPPER |
| Парткод: | 302H733020 |
| Деталь: | DUCT PU FRONT |
| Парткод: | 302H733031 |
| Деталь: | DUCT PU REAR |
| Парткод: | 302H733040 |
| Деталь: | DUCT FAN RIGHT |
| Парткод: | 302KY04010 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | PIN CURSOR |
| Парткод: | 2FB07050 |
| Деталь: | SPRING CURSOR |
| Парткод: | 2FB07060 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT,WORK PLATE |
| Парткод: | 302AR07041 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 302BC07861 |
| Деталь: | PLATE SIZE C |
| Парткод: | 302FB05200 |
| Деталь: | LEVER CURSOR A |
| Парткод: | 302FB07032 |
| Деталь: | LEVER CURSOR B |
| Парткод: | 302FB07042 |
| Деталь: | PIN CASSETTE |
| Парткод: | 302FB07420 |
| Деталь: | CURSOR RIGHT |
| Парткод: | 302FZ09030 |
| Деталь: | CURSOR RIGHT UPPER |
| Парткод: | 302FZ09040 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302FZ09070 |
| Деталь: | LABEL PAPER MAX |
| Парткод: | 302FZ09130 |
| Деталь: | LEVER CASSETTE |
| Парткод: | 302GR09051 |
| Деталь: | SPRING LEVER CASSETTE |
| Парткод: | 302GR09120 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 302GR09130 |
| Деталь: | WORK PLATE HANDLE |
| Парткод: | 302GR09150 |
| Деталь: | PLATE SIZE INCH |
| Парткод: | 302GR09201 |
| Деталь: | SEAL DETECTION PLATE |
| Парткод: | 302GR09210 |
| Деталь: | FILM PWB COVER |
| Парткод: | 302GR09250 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | WIRE CASSETTE UNIT |
| Парткод: | 302GR46450 |
| Деталь: | WORK PLATE LIFT CASSETTE |
| Парткод: | 302H009070 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302H009101 |
| Деталь: | PLATE CASSETTE EARTH |
| Парткод: | 302H009120 |
| Деталь: | LABEL PAPER SET |
| Парткод: | 302H034070 |
| Деталь: | LABEL BYPASS OPERATION |
| Парткод: | 302H708090 |
| Деталь: | LABEL JAM LEVER GUIDE |
| Парткод: | 302H708100 |
| Деталь: | COVER CASSETTE 1ST |
| Парткод: | 302H709010 |
| Деталь: | COVER CASSETTE HANDLE |
| Парткод: | 302H709030 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302H709040 |
| Деталь: | CASSETTE 1ST |
| Парткод: | 302H709050 |
| Деталь: | JOINT HANDLE CASSETTE |
| Парткод: | 302H709070 |
| Деталь: | ADJUSTING PLATE CASSETTE |
| Парткод: | 302H709080 |
| Деталь: | FRONT CURSOR CASSETTE |
| Парткод: | 302H709090 |
| Деталь: | REAR CURSOR CASSETTE |
| Парткод: | 302H709100 |
| Деталь: | RAIL CURSOR R |
| Парткод: | 302H709110 |
| Деталь: | LID PAPER SIZE |
| Парткод: | 302H709120 |
| Деталь: | RAIL CURSOR A |
| Парткод: | 302H709130 |
| Деталь: | Support Plate |
| Парткод: | 302H709140 |
| Деталь: | DETECTION PLATE PAPER SIZE |
| Парткод: | 302H709150 |
| Деталь: | CUSHION PUSH BYPASS |
| Парткод: | 302H709160 |
| Деталь: | SHEET LEVER BYPASS |
| Парткод: | 302H709170 |
| Деталь: | SPRING PAD |
| Парткод: | 302H709190 |
| Деталь: | LABEL CURSOR OPERATION |
| Парткод: | 302H734040 |
| Деталь: | LABEL CASSETTE SIZE L |
| Парткод: | 302H734050 |
| Деталь: | LABEL CASSETTE SIZE S |
| Парткод: | 302H734060 |
| Деталь: | LABEL CASSETTE OPERATION A |
| Парткод: | 302H734090 |
| Деталь: | LABEL PAPER UPPER LIMIT 1ST |
| Парткод: | 302H734180 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302KY09010 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PARTS TOP CASSETTE 1 ASSY |
| Парткод: | 302H793300 |
| Деталь: | PIN CURSORSPRING PIN /M2.5 X 14 S-BLK+TP-CUP M SCREW 4X8 R+BIND T.T P SCREW 3X8+TP-FLAT T.T P SCREW 3X8CS STOP RING /X 4 X .25T S-BLK+BIND M SCREW 3X5+TP-FLAT T.T P SCREW 3X8(BLACK)+TP-CUP M SCREW 4X8 R(BLACK)+TP-FLAT T.T P SCREW 3X6 |
| Парткод: | 302GR092205MBP2514WXSP7BB607408H7BB200308H7BB202308H5MBCS4025XSP7BB000305H7BB282308H7BB687408H7BB202306H |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | SHEET MOUNT LVU |
| Парткод: | 302H702230 |
| Деталь: | SHEET PWB 2 |
| Парткод: | 302H739910 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM110004++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | STOPPER IMAGE UNIT R |
| Парткод: | 302FZ02292 |
| Деталь: | SPRING STOPPER |
| Парткод: | 302FZ02300 |
| Деталь: | THERMISTOR |
| Парткод: | 302FZ45120 |
| Деталь: | RAIL IMAGE REAR |
| Парткод: | 302H702160 |
| Деталь: | SHEET RAIL PWB |
| Парткод: | 302H702220 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1001+H01 |
| Деталь: | RAIL IMAGE FRONT |
| Парткод: | 302H702150 |
| Деталь: | STOPPER IMAGE UNIT F |
| Парткод: | 302H702280 |
| Деталь: | HOOK DLP |
| Парткод: | 302FZ02591 |
| Деталь: | LEVER LOCK CASSETTE |
| Парткод: | 302GR02221 |
| Деталь: | SPRING LEVER |
| Парткод: | 302GR02230 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | PLATE CONTAINER RIGHT |
| Парткод: | 302H703921 |
| Деталь: | PLATE CONTAINER LEFT |
| Парткод: | 302H703910 |
| Деталь: | SHEET CONTAINER LEFT |
| Парткод: | 302H704670 |
| Деталь: | STOPPER WIRE |
| Парткод: | 302H704680 |
| Деталь: | WIRE FRONT |
| Парткод: | 302H746081 |
| Деталь: | PLATE CONTAINER CENTER |
| Парткод: | 302H703900 |
| Деталь: | HOLDER PWB FRONT |
| Парткод: | 302H703150 |
| Деталь: | WIRE RETAINER JOINT |
| Парткод: | 302H746040 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | SHUTTER CLN |
| Парткод: | 302FZ12161 |
| Деталь: | SEAL SHUTTER CLN |
| Парткод: | 302FZ12190 |
| Деталь: | SPRING SHUTTER CLN |
| Парткод: | 302FZ12220 |
| Деталь: | PIPE JOINT ICL |
| Парткод: | 302FZ23600 |
| Деталь: | SEAL PIPE WT ICL |
| Парткод: | 302FZ23640 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SCREW WT ICL |
| Парткод: | 302H703610 |
| Деталь: | GEAR WT MOTOR |
| Парткод: | 302H703630 |
| Деталь: | PIPE WT ICL |
| Парткод: | 302H703650 |
| Деталь: | SEAL ICL SCREW |
| Парткод: | 302H703830 |
| Деталь: | REAR FILM FRAME REAR |
| Парткод: | 302H733270 |
| Деталь: | REAR FILM FRAME MID |
| Парткод: | 302H733300 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SHEET WIRE DRUM |
| Парткод: | 302H702080 |
| Деталь: | SHEET CONT HOLE |
| Парткод: | 302H733770 |
| Деталь: | STAY PLATE CONTAINER |
| Парткод: | 302KA04060 |
| Деталь: | SHEET FAN RIGHT |
| Парткод: | 302KY04060 |
| Деталь: | PARTS ICL WT ASSY |
| Парткод: | 302H793350 |
| Деталь: | RACK,CURSOR |
| Парткод: | 2BC06750 |
| Деталь: | LEFT WIRE B,LIFT |
| Парткод: | 2BC07340 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | TABLE A,BYPASS |
| Парткод: | 302BC06036 |
| Деталь: | TABLE B,BYPASS |
| Парткод: | 302BC06046 |
| Деталь: | TABLE C,BYPASS |
| Парткод: | 302BC06052 |
| Деталь: | TABLE D,BYPASS |
| Парткод: | 302BC06061 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 302BC07861 |
| Деталь: | SPRING BYPASS TEBLE |
| Парткод: | 302FB17700 |
| Деталь: | GEAR 18 IDLE DEVELOPING |
| Парткод: | 302FB17710 |
| Деталь: | SEAL BYPASS TABLE |
| Парткод: | 302FB17730 |
| Деталь: | SIZE INDICATOR BYPASS(I) |
| Парткод: | 302FB17750 |
| Деталь: | SIZE INDICATOR BYPASS(M) |
| Парткод: | 302FB17740 |
| Деталь: | PIN BYPASS TABLE |
| Парткод: | 302FB17800 |
| Деталь: | SWITCH BYPASS SIZE |
| Парткод: | 302FB25140 |
| Деталь: | PAD MP L |
| Парткод: | 302FZ08500 |
| Деталь: | LABEL MP CAUTION E S |
| Парткод: | 302H708050 |
| Деталь: | LABEL ORIGINAL MAX |
| Парткод: | 302H708070 |
| Деталь: | LABEL MP CAUTION PIC S |
| Парткод: | 302H708080 |
| Деталь: | CURSOR MPT F |
| Парткод: | 302H708110 |
| Деталь: | CURSOR MPT R |
| Парткод: | 302H708120 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 302H746980 |
| Деталь: | FRICTION PLATE,BYPASS |
| Парткод: | 33906400 |
| Деталь: | COVER,CURSOR |
| Парткод: | 33906900 |
| Деталь: | ORIGINAL SIZE SWITCH |
| Парткод: | 76727010 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM420003++H01 |
| Деталь: | LABEL MP CAUTION SET E |
| Парткод: | 302H708140 |
| Деталь: | PARTS MPT TRAY UNIT(U) |
| Парткод: | 302H793550 |
| Деталь: | PARTS MPT TRAY UNIT(E) |
| Парткод: | 302H793560 |
| Деталь: | PARTS MOTOR DU SP |
| Парткод: | 302KY94070 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SHAFT MIDDLE L |
| Парткод: | 302FZ22140 |
| Деталь: | RETAINER ACTUATOR DU |
| Парткод: | 302FZ29080 |
| Деталь: | BELT DU |
| Парткод: | 302FZ29110 |
| Деталь: | PULLEY DU BELT |
| Парткод: | 302FZ29120 |
| Деталь: | SPRING DU |
| Парткод: | 302FZ29131 |
| Деталь: | COLLAR DU PULLEY |
| Парткод: | 302FZ29140 |
| Деталь: | PARTS, ROLLER DUPLEX A SP |
| Парткод: | 302FZ94620 |
| Деталь: | PARTS ROLLER DUPLEX B SP |
| Парткод: | 302KA94220 |
| Деталь: | SPRING EARTH PLATE LEFT |
| Парткод: | 302H722420 |
| Деталь: | SHEET DUCT LOOP 1 |
| Парткод: | 302H722710 |
| Деталь: | SHEET DUCT LOOP 2 |
| Парткод: | 302H722720 |
| Деталь: | BUSH SP B |
| Парткод: | 302H722730 |
| Деталь: | FRAME DU |
| Парткод: | 302H729011 |
| Деталь: | GEAR DU IDLE Z45S |
| Парткод: | 302H729020 |
| Деталь: | MOUNT MOTOR DU HIGH |
| Парткод: | 302H729030 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 302H729060 |
| Деталь: | GEAR Z32S DU |
| Парткод: | 302KA29020 |
| Деталь: | SPRING EARTH PLATE DU |
| Парткод: | 302H729100 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302H729110 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | PLATE EARTH MOTOR DU |
| Парткод: | 302H729130 |
| Деталь: | SHEET WIRE CL |
| Парткод: | 302H732230 |
| Деталь: | WIRE DU OPEN SW |
| Парткод: | 302H746800 |
| Деталь: | COVER FILTER OPTION |
| Парткод: | 302H733680 |
| Деталь: | FILTER OPTION |
| Парткод: | 302H733690 |
| Деталь: | PARTS DUCT OPTION UNIT Q |
| Парткод: | 302H794600 |
| Деталь: | PARTS DUCT OPTION UNIT |
| Парткод: | 302H794580 |
| Деталь: | PARTS DUCT OPTION UNIT P |
| Парткод: | 302H794590 |
| Деталь: | PARTS PWB LED ASSY SP |
| Парткод: | 302H794150 |
| Деталь: | PARTS FAN COOLING CONV |
| Парткод: | 302H794490 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+020H01 |
| Деталь: | SHEET LEFT ACT |
| Парткод: | 302H724300 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | WIRE JAM LED2 |
| Парткод: | 302H746830 |
| Деталь: | LABEL VFEED CAUTION |
| Парткод: | 302FB05380 |
| Деталь: | SHAFT LEFT COVER |
| Парткод: | 302FZ04310 |
| Деталь: | LEVER LEFT COVER |
| Парткод: | 302FZ04321 |
| Деталь: | SHAFT LEFT COVER B |
| Парткод: | 302FZ04420 |
| Деталь: | WIRE JAM LED1 |
| Парткод: | 302H746820 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H017180 |
| Деталь: | LABEL HIGH TEMP CAUTION |
| Парткод: | 302KA34020 |
| Деталь: | COVER PWB FEED |
| Парткод: | 302H722020 |
| Деталь: | SHAFT HOOK CONVEYING |
| Парткод: | 302H722110 |
| Деталь: | SPRING CONVEYING F |
| Парткод: | 302H722150 |
| Деталь: | SPRING CONVEYING R |
| Парткод: | 302H722160 |
| Деталь: | COVER LEFT |
| Парткод: | 302H722201 |
| Деталь: | SHAFT HOOK |
| Парткод: | 302H722240 |
| Деталь: | JOINT HOOK CONVEYING |
| Парткод: | 302H722250 |
| Деталь: | COVER LEFT DU |
| Парткод: | 302H722262 |
| Деталь: | STOPPER COVER DU |
| Парткод: | 302H722270 |
| Деталь: | SPRING COVER DU |
| Парткод: | 302H722280 |
| Деталь: | COVER LED LEFT |
| Парткод: | 302H722292 |
| Деталь: | SHEET COVER LEFT |
| Парткод: | 302H722310 |
| Деталь: | SHEET PLATE LEFT |
| Парткод: | 302H722320 |
| Деталь: | GUIDE LEFT DU |
| Парткод: | 302H722330 |
| Деталь: | SHEET RELEASE CORD |
| Парткод: | 302H722340 |
| Деталь: | COVER FILTER DU |
| Парткод: | 302H722490 |
| Деталь: | SHEET WIRE CONV E |
| Парткод: | 302H722690 |
| Деталь: | LABEL LEFT COVER HANDLE |
| Парткод: | 302H722780 |
| Деталь: | FILTER DU |
| Парткод: | 302H722870 |
| Деталь: | SHEET WIRE LED |
| Парткод: | 302H724210 |
| Деталь: | PLATE LEFT COVER ASSY |
| Парткод: | 302KA22010 |
| Деталь: | SPRING DAMPER CONV |
| Парткод: | 302H724060 |
| Деталь: | WIRE DAMPER CONV |
| Парткод: | 302H724070 |
| Деталь: | PLATE DAMPER A |
| Парткод: | 302H724080 |
| Деталь: | COVER DAMPER SPRING |
| Парткод: | 302H724100 |
| Деталь: | HOOK CONVEYING S F |
| Парткод: | 302H724140 |
| Деталь: | HOOK CONVEYING S R |
| Парткод: | 302H724150 |
| Деталь: | SHEET DAMPER SPRING |
| Парткод: | 302H724200 |
| Деталь: | PLATE PIN WIRE CONV |
| Парткод: | 302H724110 |
| Деталь: | BAND LEFT COVER |
| Парткод: | 302FZ04990 |
| Деталь: | LABEL VFEED CAUTION |
| Парткод: | 302FB05441 |
| Деталь: | MOUNT SHAFT CAM |
| Парткод: | 302FZ02700 |
| Деталь: | MOUNT SOLENOID |
| Парткод: | 302FZ02691 |
| Деталь: | SOLENOID LSU CLN |
| Парткод: | 302H744060 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GUIDE FEED LOW 1ST |
| Парткод: | 302FZ22802 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | FILM WIRE GUIDE |
| Парткод: | 302H724220 |
| Деталь: | WIRE GUIDE FEED LOW1 |
| Парткод: | 302H746500 |
| Деталь: | PARTS ROLLER FEED LOW |
| Парткод: | 302H794200 |
| Деталь: | PARTS SWITCH CONVEYING B |
| Парткод: | 302H794210 |
| Деталь: | Guide Wire |
| Парткод: | 303LM24050 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | GUIDE FEED UP 2ND |
| Парткод: | 302FZ22830 |
| Деталь: | GUIDE FEED LOW 2ND |
| Парткод: | 302H722660 |
| Деталь: | WIRE GUIDE FEED LOW2 |
| Парткод: | 302H746510 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | CAM SHAFT BLADE |
| Парткод: | 302FZ02671 |
| Деталь: | SHAFT CLN LSU |
| Парткод: | 302FZ02682 |
| Деталь: | CLUTCH LSU CLEANING |
| Парткод: | 302FZ02741 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ROLLER REGIST R |
| Парткод: | 302FZ22040 |
| Деталь: | GEAR REGIST Z18H |
| Парткод: | 302FZ22120 |
| Деталь: | BEARING 688ZZNR |
| Парткод: | 7BE08165Z131H01 |
| Цена: | 500 ₽ |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | LABEL JAM BYPASS B1 |
| Парткод: | 302FZ07340 |
| Деталь: | SHAFT MIDDLE L |
| Парткод: | 302FZ22140 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302FZ22160 |
| Деталь: | SPRING MIDDLE |
| Парткод: | 302FZ22341 |
| Деталь: | SHEET REGIST |
| Парткод: | 302FZ22380 |
| Деталь: | SHEET MIDDLE BYPASS |
| Парткод: | 302FZ22460 |
| Деталь: | LEVER MIDDLE F |
| Парткод: | 302FZ22500 |
| Деталь: | LEVER MIDDLE R |
| Парткод: | 302FZ22520 |
| Деталь: | SPRING MID LEVER F |
| Парткод: | 302FZ22600 |
| Деталь: | SPRING MID LEVER R |
| Парткод: | 302FZ22610 |
| Деталь: | SPRING ACTUATOR REGIST |
| Парткод: | 302FZ22621 |
| Деталь: | ACTUATOR MID BYPASS |
| Парткод: | 302FZ22840 |
| Деталь: | SPRING ACTUATOR BYPASS |
| Парткод: | 302FZ22870 |
| Деталь: | PARTS,ROLLER MIDDLE R SP |
| Парткод: | 302FZ94540 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | GUIDE MIDDLE R |
| Парткод: | 302H722500 |
| Деталь: | WIRE GUIDE MIDDLE |
| Парткод: | 302H722510 |
| Деталь: | PLATE EARTH SHAFT |
| Парткод: | 302H722520 |
| Деталь: | GEAR MIDDLE A |
| Парткод: | 302H722530 |
| Деталь: | GEAR MIDDLE B |
| Парткод: | 302H722540 |
| Деталь: | GEAR MIDDLE Z19S |
| Парткод: | 302H722550 |
| Деталь: | GUIDE MIDDLE LOW |
| Парткод: | 302H722600 |
| Деталь: | GUIDE MIDDLE BYPASS |
| Парткод: | 302H722610 |
| Деталь: | PLATE SENS MIDDLE |
| Парткод: | 302H722620 |
| Деталь: | SPRING EARTH MID LOW |
| Парткод: | 302H722630 |
| Деталь: | SPRING EARTH SENS |
| Парткод: | 302H722640 |
| Деталь: | GUIDE FEED R |
| Парткод: | 302H722700 |
| Деталь: | BUSH SP B |
| Парткод: | 302H722730 |
| Деталь: | HOLDER MIDDLE R |
| Парткод: | 302H724190 |
| Деталь: | SHEET WIRE LED |
| Парткод: | 302H724210 |
| Деталь: | CENTER SPONGE GUIDE FEED |
| Парткод: | 302H724270 |
| Деталь: | CENTER FILM GUIDE FEED |
| Парткод: | 302H724281 |
| Деталь: | FILM GUIDE HOLE |
| Парткод: | 302H724290 |
| Деталь: | WIRE FEED SENS |
| Парткод: | 302H746550 |
| Деталь: | PARTS ROLLER MIDDLE BYPASS |
| Парткод: | 302H794340 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | GUIDE FEED UP 1ST |
| Парткод: | 302FZ22820 |
| Деталь: | PARTS GUIDE FEED LOW 1ST ASSY |
| Парткод: | 302H794510 |
| Деталь: | PARTS GUIDE FEED LOW2 H |
| Парткод: | 302H794500 |
| Деталь: | PARTS GUIDE MIDDLE H UNIT |
| Парткод: | 302H794520 |
| Деталь: | CONT BOX |
| Парткод: | 302H739010 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302KA94010 |
| Деталь: | PARTS PWB MAIN ASSY SP EU |
| Парткод: | 302KA94020 |
| Деталь: | PARTS PWB CODE DIMM ASSY SP |
| Парткод: | 302KA94050 |
| Деталь: | PARTS MEMORY MODULE SP |
| Парткод: | 302KA94150 |
| Деталь: | PIN HINGE A |
| Парткод: | 302H739200 |
| Деталь: | WIRE MAIN-KUIO |
| Парткод: | 302H746730 |
| Деталь: | PLATE OPTION |
| Парткод: | 2DD26070 |
| Деталь: | FAN BOX COOLING |
| Парткод: | 302FZ44040 |
| Деталь: | RAIL PWB |
| Парткод: | 302H739040 |
| Деталь: | MOUNT FAN MAIN |
| Парткод: | 302H739170 |
| Деталь: | LID DP |
| Парткод: | 302H739260 |
| Деталь: | FILM CONT BOX |
| Парткод: | 302H739320 |
| Деталь: | GUIDE CF |
| Парткод: | 302H739770 |
| Деталь: | NYLON CLAMP 3N,NK-3N |
| Парткод: | M2105010 |
| Деталь: | BRACKET HDD |
| Парткод: | 302H739020 |
| Деталь: | PARTS HDD |
| Парткод: | 302K593040 |
| Деталь: | WIRE CF |
| Парткод: | 302H746740 |
| Деталь: | WIRE HDD POWER (L) |
| Парткод: | 302JZ46150 |
| Деталь: | WIRE HDD DATA1 |
| Парткод: | 302H746900 |
| Деталь: | PARTS PWB KUIO IF ASSY SP |
| Парткод: | 302H794031 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS PWB CF ASSY SP |
| Парткод: | 302H794020 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | PARTS FUSER UNIT A |
| Парткод: | 302KA93011 |
| Деталь: | PARTS FUSER UNIT E |
| Парткод: | 302KA93022 |
| Деталь: | SHEET LSU WIRE |
| Парткод: | 302H702450 |
| Деталь: | MOUNT HINGE |
| Парткод: | 302H704530 |
| Деталь: | SHEET INTERCEPT FUSER |
| Парткод: | 302H733700 |
| Деталь: | STAY UPPER REAR |
| Парткод: | 302KA02010 |
| Деталь: | LABEL CONTAINER T1 |
| Парткод: | 4AK73740 |
| Деталь: | LABEL CONTAINER T2 |
| Парткод: | 4AK73750 |
| Деталь: | LABEL CONTAINER T3 |
| Парткод: | 4AK73760 |
| Деталь: | LABEL CONTAINER T4 |
| Парткод: | 4AK73770 |
| Деталь: | SPRING EARTH EXIT |
| Парткод: | 302FZ02510 |
| Деталь: | Plate Fuser |
| Парткод: | 302FZ02720 |
| Деталь: | FRAME FUSER UNIT CENTER |
| Парткод: | 302H702250 |
| Деталь: | WIRE FUSER JOINT |
| Парткод: | 302H746191 |
| Деталь: | STAY UPPER LEFT |
| Парткод: | 302HP02060 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302HP02080 |
| Деталь: | PLATE EARTH FUSER |
| Парткод: | 302HP02090 |
| Деталь: | FRAME FUSER UNIT F |
| Парткод: | 302KA02030 |
| Деталь: | FRAME FUSER UNIT R |
| Парткод: | 302KA02041 |
| Деталь: | PLATE FRAME FUSER F |
| Парткод: | 302KA02050 |
| Деталь: | STAY OPERATION WIRE |
| Парткод: | 302KA02060 |
| Деталь: | SHEET OPERATION WIRE |
| Парткод: | 302KA02080 |
| Деталь: | SHEET FRAME FUSER F |
| Парткод: | 302KA02120 |
| Деталь: | SHEET COVER EXIT WIRE |
| Парткод: | 302KA28060 |
| Деталь: | PIN,DRAWER SIDE CONVEYING |
| Парткод: | 3CZ02240 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | STAY SHIELD BOX |
| Парткод: | 302H739030 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTG15C050H01 |
| Деталь: | STAY UPPER RIGHT |
| Парткод: | 302KA02020 |
| Деталь: | SHEET UPPER REAR |
| Парткод: | 302KA02110 |
| Деталь: | NYLON CLAMP 3N,NK-3N |
| Парткод: | M2105010 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SPRING COUPLING DLP |
| Парткод: | 302BG22531 |
| Деталь: | COUPLING DLP DRIVE |
| Парткод: | 302FZ31250 |
| Деталь: | COLLAR DLP COUPLING |
| Парткод: | 302FZ31280 |
| Деталь: | GEAR Z22R |
| Парткод: | 302FZ31350 |
| Деталь: | PIN MAIN DRIVE |
| Парткод: | 302FZ31720 |
| Деталь: | GEAR Z22L CLN |
| Парткод: | 302FZ31850 |
| Деталь: | PIN DLP DRIVE |
| Парткод: | 302FZ32150 |
| Деталь: | HOLDER MAIN DRIVE |
| Парткод: | 302H731310 |
| Деталь: | PLATE MAIN DRIVE |
| Парткод: | 302H731320 |
| Деталь: | SHAFT CLN DRIVE |
| Парткод: | 302H731400 |
| Деталь: | SHAFT DLP DRIVE MK |
| Парткод: | 302H731410 |
| Деталь: | SHAFT DLP DRIVE CY |
| Парткод: | 302H731420 |
| Деталь: | GEAR Z68L Z29L MAIN |
| Парткод: | 302H731430 |
| Деталь: | GEAR Z70L Z22L MAIN |
| Парткод: | 302H731440 |
| Деталь: | GEAR Z70L Z22R |
| Парткод: | 302H731450 |
| Деталь: | GEAR Z42R MAIN |
| Парткод: | 302H731460 |
| Деталь: | GEAR Z48L MAIN |
| Парткод: | 302H731470 |
| Деталь: | GEAR Z60R MAIN |
| Парткод: | 302H731480 |
| Деталь: | GEAR Z50R MAIN |
| Парткод: | 302H731490 |
| Деталь: | GEAR Z36L MAIN |
| Парткод: | 302H731500 |
| Деталь: | GUIDE MAIN DRIVE |
| Парткод: | 302H739310 |
| Деталь: | GEAR Z31L |
| Парткод: | 302JD31170 |
| Деталь: | GEAR Z22L DLP |
| Парткод: | 302KY31010 |
| Деталь: | GEAR Z50L |
| Парткод: | 302KY31020 |
| Деталь: | GEAR Z60L CLN |
| Парткод: | 302KY31040 |
| Деталь: | PARTS MOTOR DLP SP |
| Парткод: | 302KY94100 |
| Деталь: | PARTS MOTOR CLN SP |
| Парткод: | 302KY94110 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE RUB/DLP MOT |
| Парткод: | 302H746220 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | PARTS MAIN DRIVE H UNIT |
| Парткод: | 302KY93140 |
| Деталь: | HOLDER GUIDE PULLEY |
| Парткод: | 302FZ21700 |
| Деталь: | PULLEY GUIDE |
| Парткод: | 302FZ25940 |
| Деталь: | GUIDE BELT UP |
| Парткод: | 302H721120 |
| Деталь: | PARTS FAN IMAGE |
| Парткод: | 302H794700 |
| Деталь: | PARTS TRANSFER BELT UNIT |
| Парткод: | 302KY93151 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | LEVER LEFT COVER |
| Парткод: | 302FZ04321 |
| Деталь: | SPRING LEFT COVER F |
| Парткод: | 302FZ04390 |
| Деталь: | SPRING LEFT COVER R |
| Парткод: | 302FZ04400 |
| Деталь: | SHAFT MIDDLE L |
| Парткод: | 302FZ22140 |
| Деталь: | PULLEY EXIT |
| Парткод: | 302H728050 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 302FZ25380 |
| Деталь: | GEAR Z20S-Z23S |
| Парткод: | 302FZ28060 |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | 302FZ28080 |
| Деталь: | GEAR Z29S |
| Парткод: | 302FZ28090 |
| Деталь: | SPRING EARTH |
| Парткод: | 302FZ28120 |
| Деталь: | EXIT PUSH |
| Парткод: | 302FZ28260 |
| Деталь: | SPRING EXIT PUSH |
| Парткод: | 302FZ28270 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PULLEY EXIT B |
| Парткод: | 302H728310 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302HP04091 |
| Деталь: | SHAFT HOOK |
| Парткод: | 302HP04100 |
| Деталь: | HOOK LID F |
| Парткод: | 302HP04111 |
| Деталь: | HOOK LID R |
| Парткод: | 302HP04120 |
| Деталь: | ROLLER EXIT IN |
| Парткод: | 302HP28041 |
| Деталь: | ROLLER EXIT OUT |
| Парткод: | 302HP28050 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302HP28060 |
| Деталь: | FRAME EXIT LOW |
| Парткод: | 302HP28071 |
| Деталь: | FRAME EXIT ENTRANCE |
| Парткод: | 302HP28080 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 302HP28100 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 302HP28110 |
| Деталь: | ACTUATOR EXIT ENTRANCE |
| Парткод: | 302HP28120 |
| Деталь: | GUIDE CHANGE R |
| Парткод: | 302HP28130 |
| Деталь: | GUIDE CHANGE L |
| Парткод: | 302HP28140 |
| Деталь: | GUIDE ENTRANCE |
| Парткод: | 302KA28080 |
| Деталь: | FRAME EXIT MIDDLE |
| Парткод: | 302HP28191 |
| Деталь: | PLATE EXIT DRIVE |
| Парткод: | 302HP28220 |
| Деталь: | SHAFT GEAR EXIT |
| Парткод: | 302HP28230 |
| Деталь: | SPRING ACT EXIT L |
| Парткод: | 302HP28240 |
| Деталь: | SPRING ACT EXIT R |
| Парткод: | 302HP28250 |
| Деталь: | HOLDER EXIT PULLEY |
| Парткод: | 302HP28261 |
| Деталь: | PLATE EXIT SOL |
| Парткод: | 302HP28280 |
| Деталь: | COVER PWB |
| Парткод: | 302HP28291 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302HP28320 |
| Деталь: | ARM SOLENOID |
| Парткод: | 302HP28330 |
| Деталь: | PLATE EARTH EXIT B |
| Парткод: | 302HP28360 |
| Деталь: | SHEET EXIT |
| Парткод: | 302HP28370 |
| Деталь: | SEAL ACT |
| Парткод: | 302HP28390 |
| Деталь: | SPRING EXIT EARTH |
| Парткод: | 302HP28400 |
| Деталь: | STATIC ELIMINATOR PR |
| Парткод: | 302HP28450 |
| Деталь: | SHEET EXIT WIRE |
| Парткод: | 302HP28460 |
| Деталь: | Bush SP |
| Парткод: | 302HP28520 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 302HP28530 |
| Деталь: | GEAR Z58-Z21 |
| Парткод: | 302HP31030 |
| Деталь: | GEAR Z20 DU |
| Парткод: | 302HP31040 |
| Деталь: | GEAR Z31 |
| Парткод: | 302HP31050 |
| Деталь: | GEAR Z29 |
| Парткод: | 302HP31060 |
| Деталь: | SOLENOID EXIT |
| Парткод: | 302HP44020 |
| Деталь: | ACTUATOR EXIT FULL |
| Парткод: | 302KA28010 |
| Деталь: | Guide Wire |
| Парткод: | 302KA28030 |
| Деталь: | SPRING SOL |
| Парткод: | 302KA28040 |
| Деталь: | WIRE EJECT |
| Парткод: | 302KA46010 |
| Деталь: | WIRE OP-DU PI |
| Парткод: | 302KA46040 |
| Деталь: | PARTS ROLLER EXIT PR SP |
| Парткод: | 302KA94060 |
| Деталь: | PARTS MOTOR EXIT PR SP |
| Парткод: | 302KA94070 |
| Деталь: | SPRING SOL A |
| Парткод: | 303KN16180 |
| Деталь: | SEAL ACT |
| Парткод: | 303KN16311 |
| Деталь: | PARTS,PRINTED W.BOARD JOB,SP |
| Парткод: | 303KN94010 |
| Деталь: | PARTS,SOLENOID,SP |
| Парткод: | 303KN94040 |
| Деталь: | BUSH SP /40613P5004 A4 |
| Парткод: | 5MVF111DN005 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SHEET COVER TOP |
| Парткод: | 302KA04140 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302KA28070 |
| Деталь: | PLATE RADIATOR SOLENOID |
| Парткод: | 302KA28090 |
| Деталь: | THERMAL SHEET |
| Парткод: | 7ZS24133001+H01 |
| Деталь: | COVER LEFT MIDDLE |
| Парткод: | 302HP04040 |
| Деталь: | SHEET COVER LEFT A |
| Парткод: | 302KA04120 |
| Деталь: | SHEET COVER LEFT B |
| Парткод: | 302KA04130 |
| Деталь: | PARTS EXIT ASSY SP |
| Парткод: | 302KA94140 |
| Деталь: | GEAR Z14S |
| Парткод: | 302FZ14230 |
| Деталь: | COVER FRONT BK DLP |
| Парткод: | 302H714230 |
| Деталь: | COVER REAR BK DLP |
| Парткод: | 302H714320 |
| Деталь: | UPPER DUCT DLP |
| Парткод: | 302H714630 |
| Деталь: | SEAL TAKEOFF |
| Парткод: | 302H715350 |
| Деталь: | GEAR MAG Z25H |
| Парткод: | 302KY14050 |
| Деталь: | GEAR SLEEVE Z24H |
| Парткод: | 302KY14060 |
| Деталь: | GEAR IDLE Z22H |
| Парткод: | 302KY14070 |
| Деталь: | COVER FRONT C DLP |
| Парткод: | 302H714470 |
| Деталь: | COVER REAR C DLP |
| Парткод: | 302H714500 |
| Деталь: | COVER FRONT Y DLP |
| Парткод: | 302H714480 |
| Деталь: | COVER REAR Y DLP |
| Парткод: | 302H714510 |
| Деталь: | COVER FRONT M DLP |
| Парткод: | 302H714490 |
| Деталь: | COVER REAR M DLP |
| Парткод: | 302H714520 |
| Деталь: | STUD SCREW M4 |
| Парткод: | 302JF14010 |
| Деталь: | PARTS DLP K UNIT |
| Парткод: | 302KY93030 |
| Деталь: | PARTS DLP C UNIT |
| Парткод: | 302KY93040 |
| Деталь: | PARTS DLP Y UNIT |
| Парткод: | 302KY93050 |
| Деталь: | PARTS DLP M UNIT |
| Парткод: | 302KY93060 |
| Деталь: | GEAR Z14R LSU |
| Парткод: | 302FZ31440 |
| Деталь: | GEAR Z25R JOINT |
| Парткод: | 302FZ31800 |
| Деталь: | COUPLING PAPER FEED |
| Парткод: | 302FZ32070 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SHEEL FEED DRIVE |
| Парткод: | 302H731100 |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 302H731110 |
| Деталь: | Plate Regist |
| Парткод: | 302H731120 |
| Деталь: | PLATE FEED |
| Парткод: | 302H731130 |
| Деталь: | SHAFT FEED DRIVE A |
| Парткод: | 302H731140 |
| Деталь: | SHAFT FEED DRIVE B |
| Парткод: | 302H731150 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 302H731160 |
| Деталь: | GEAR Z47L Z26L FEED |
| Парткод: | 302H731170 |
| Деталь: | GEAR Z32R Z23R FEED |
| Парткод: | 302H731180 |
| Деталь: | GEAR Z22R FEED |
| Парткод: | 302H731190 |
| Деталь: | GEAR Z27R FEED |
| Парткод: | 302H731200 |
| Деталь: | GEAR Z23L FEED |
| Парткод: | 302H731210 |
| Деталь: | SHAFT MIDDLE DRIVE |
| Парткод: | 302H731220 |
| Деталь: | SHAFT LSU DRIVE |
| Парткод: | 302H731230 |
| Деталь: | GEAR Z42L FEED |
| Парткод: | 302H731240 |
| Деталь: | GEAR Z22L MOTOR |
| Парткод: | 302H731250 |
| Деталь: | GEAR Z43R MIDDLE |
| Парткод: | 302H731260 |
| Деталь: | GEAR Z29R MIDDLE |
| Парткод: | 302H731280 |
| Деталь: | GEAR Z32R Z20L MIDDLE |
| Парткод: | 302H731720 |
| Деталь: | GEAR Z34L MIDDLE |
| Парткод: | 302H731730 |
| Деталь: | GEAR Z48R MIDDLE |
| Парткод: | 302H731740 |
| Деталь: | GEAR Z51L Z23L FEED |
| Парткод: | 302H731750 |
| Деталь: | PIN DRIVE MIDDLE |
| Парткод: | 302H731810 |
| Деталь: | SHEET WIRE CL |
| Парткод: | 302H732230 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302H739110 |
| Деталь: | PLATE EARTH MIDDLE |
| Парткод: | 302H739150 |
| Деталь: | WIRE REG/ROL MOT |
| Парткод: | 302H746480 |
| Деталь: | WIRE FEED MOT |
| Парткод: | 302H746490 |
| Деталь: | WIRE CASSETTE |
| Парткод: | 302H746530 |
| Деталь: | PARTS PWB FEED ASSY SP |
| Парткод: | 302H794100 |
| Деталь: | PARTS MOTOR REGIST |
| Парткод: | 302H794230 |
| Деталь: | PARTS CLUTCH FEED 50 |
| Парткод: | 302H794240 |
| Деталь: | STUD SCREW 435 |
| Парткод: | 302JF31010 |
| Деталь: | PARTS MOTOR FEED SP |
| Парткод: | 302KY94090 |
| Деталь: | CUT WASHER |
| Парткод: | 5MVS665KB001 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | COVER DRUM SENSOR |
| Парткод: | 302H731390 |
| Деталь: | CUT WASHER 10 |
| Парткод: | 302H731990 |
| Деталь: | SEAL DRUM DRIVE |
| Парткод: | 302H732020 |
| Деталь: | WIRE DRUM MOT |
| Парткод: | 302H746750 |
| Деталь: | PARTS MOTOR DRUM |
| Парткод: | 302H793080 |
| Деталь: | SHEET DRUM SENSOR |
| Парткод: | 302JZ31330 |
| Деталь: | BEARING 6801ZZ |
| Парткод: | 7BE6801ZZ+++H01 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM410001++H01 |
| Деталь: | PARTS PWB MOTOR CONTROL ASSY SP |
| Парткод: | 302H794090 |
| Деталь: | PLATE MOTOR PWB |
| Парткод: | 302H739210 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | THERMAL SHEET |
| Парткод: | 7ZS46175001+H01 |
| Деталь: | WIRE MOT CONTROL |
| Парткод: | 302H746290 |
| Деталь: | COVER MOTOR PWB |
| Парткод: | 302H739230 |
| Деталь: | SHEET MOTOR PWB |
| Парткод: | 302H739240 |
| Деталь: | PARTS FEED DRIVE H UNIT |
| Парткод: | 302KY93090 |
| Деталь: | PARTS DRUM DRIVE H UNIT |
| Парткод: | 302H793331 |
| Деталь: | 20305130 |
| Парткод: | 20305130 |
| Деталь: | 2H702210 |
| Парткод: | 302H702210 |
| Деталь: | 2H794620 |
| Парткод: | 302H794620 |
| Деталь: | 2H794760 |
| Парткод: | 302H794760 |
| Деталь: | VARISTOR TC ASSY |
| Парткод: | 302FZ01310 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | GEAR REGIST Z22H |
| Парткод: | 302FZ22130 |
| Деталь: | PLATE DISCHARGER |
| Парткод: | 302FZ22201 |
| Деталь: | CONTACT DISCHARGE |
| Парткод: | 302FZ22230 |
| Деталь: | PLATE EARTH REGIST |
| Парткод: | 302FZ22241 |
| Деталь: | SPRING MIDDLE |
| Парткод: | 302FZ22341 |
| Деталь: | SPRING GUIDE TRANSFER |
| Парткод: | 302FZ22350 |
| Деталь: | BUSH REGIST |
| Парткод: | 302FZ22560 |
| Деталь: | SHEET MIDDLE L |
| Парткод: | 302FZ22720 |
| Деталь: | SHEET REGIST L |
| Парткод: | 302FZ24010 |
| Деталь: | SHEET DISCHARGER |
| Парткод: | 302FZ24240 |
| Деталь: | SEAL FAN CONV B |
| Парткод: | 302FZ24550 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS,ROLLER REGIST L SP |
| Парткод: | 302FZ94520 |
| Деталь: | WIRE DU |
| Парткод: | 302KA46160 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302H722010 |
| Деталь: | SPRING EARTH FEED UNIT |
| Парткод: | 302H722050 |
| Деталь: | GUIDE CONVEYING TC |
| Парткод: | 302H722060 |
| Деталь: | PLATE GUIDE CONVEYING H |
| Парткод: | 302H722070 |
| Деталь: | WIRE LOOP SENS |
| Парткод: | 302H746950 |
| Деталь: | GUIDE MIDDLE L |
| Парткод: | 302H722090 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302H722120 |
| Деталь: | PLATE EARTH CONVEYING |
| Парткод: | 302H722130 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | 302H722170 |
| Деталь: | SPRING TRANSFER R |
| Парткод: | 302H722180 |
| Деталь: | SHEET PLATE LEFT |
| Парткод: | 302H722320 |
| Деталь: | HOLDER DISCHARGER |
| Парткод: | 302H722350 |
| Деталь: | SPRING EARTH GUIDE TC |
| Парткод: | 302H722390 |
| Деталь: | RETAINER SENS LOOP |
| Парткод: | 302H722440 |
| Деталь: | PLATE SENSOR LOOP |
| Парткод: | 302H722450 |
| Деталь: | SHEET WIRE CONV C |
| Парткод: | 302H722670 |
| Деталь: | SHEET WIRE CONV R |
| Парткод: | 302H722680 |
| Деталь: | BUSH SP B |
| Парткод: | 302H722730 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | SHAFT MIDDLE A |
| Парткод: | 302H722770 |
| Деталь: | SPRING CONTACT DISCHARGER |
| Парткод: | 302H722820 |
| Деталь: | SHEET FAN COVEYING |
| Парткод: | 302H722860 |
| Деталь: | CONTACT TRANSFER |
| Парткод: | 302H722900 |
| Деталь: | PLATE EARTH FAN |
| Парткод: | 302H722910 |
| Деталь: | BUSH10 REGIST C |
| Парткод: | 302H724010 |
| Деталь: | SPRING REGIST C |
| Парткод: | 302H724020 |
| Деталь: | SPRING REGIST F |
| Парткод: | 302H724030 |
| Деталь: | SPRING REGIST R |
| Парткод: | 302H724040 |
| Деталь: | WIRE EARTH |
| Парткод: | 302H746960 |
| Деталь: | SHEET CONV MID |
| Парткод: | 302H724180 |
| Деталь: | STOPPER TRANS BEARING |
| Парткод: | 302H724170 |
| Деталь: | PARTS SENSOR OPT |
| Парткод: | 302H794550 |
| Деталь: | WIRE TC GUIDE |
| Парткод: | 302FZ46861 |
| Деталь: | PARTS CONVEYING H UNIT SP |
| Парткод: | 302KA94130 |
| Деталь: | PARTS ROLLER TRANSFER ASSY SP |
| Парткод: | 302KY94300 |
| Деталь: | PARTS GUIDE TC L UNIT |
| Парткод: | 302H794730 |
| Деталь: | BRACKET MPT GEAR |
| Парткод: | 302FZ07500 |
| Деталь: | GEAR JOINT MPT |
| Парткод: | 302FZ07510 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | GUIDE BYPASS RIGHT |
| Парткод: | 302FZ07061 |
| Деталь: | COVER BYPASS OUT |
| Парткод: | 302FZ07071 |
| Деталь: | BELT BYPASS |
| Парткод: | 302FZ07090 |
| Деталь: | GEAR BYPASS A |
| Парткод: | 302FZ07100 |
| Деталь: | GEAR BYPASS JOINT |
| Парткод: | 302FZ07120 |
| Деталь: | COVER MPT REAR |
| Парткод: | 302FZ07140 |
| Деталь: | PULLEY TENSION BELT |
| Парткод: | 302FZ07150 |
| Деталь: | PLATE EARTH MPT |
| Парткод: | 302FZ07180 |
| Деталь: | SPRING EARTH BYPASS JOINT |
| Парткод: | 302FZ07210 |
| Деталь: | SLIDER BYPASS A |
| Парткод: | 302FZ07240 |
| Деталь: | SLIDER BYPASS B |
| Парткод: | 302FZ07250 |
| Деталь: | PLATE GUIDE MPT |
| Парткод: | 302FZ07302 |
| Деталь: | BUSH CONTACT MPT B |
| Парткод: | 302FZ07310 |
| Деталь: | SPRING EARTH MPT A |
| Парткод: | 302FZ07320 |
| Деталь: | SPRING EARTH MPT B |
| Парткод: | 302FZ07330 |
| Деталь: | SPRING BYPASS PULLEY B |
| Парткод: | 302FZ07380 |
| Деталь: | LABEL JAM BYPASS B4 |
| Парткод: | 302FZ07420 |
| Деталь: | HOLDER SHAFT OUT |
| Парткод: | 302FZ07540 |
| Деталь: | SHEET BYPASS OUT |
| Парткод: | 302FZ07550 |
| Деталь: | COLLAR DU PULLEY |
| Парткод: | 302FZ29140 |
| Деталь: | PARTS, ROLLER BYPASS A SP |
| Парткод: | 302FZ94472 |
| Деталь: | PARTS, ROLLER BYPASS B SP |
| Парткод: | 302FZ94481 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BASE MPF BYPASS |
| Парткод: | 302H707010 |
| Деталь: | HANDLE BYPASS |
| Парткод: | 302H707020 |
| Деталь: | LEVER PUSH BYPASS |
| Парткод: | 302H707030 |
| Деталь: | LEVER JAM BYPASS |
| Парткод: | 302H707040 |
| Деталь: | SPRING LEVER BYPASS |
| Парткод: | 302H707050 |
| Деталь: | PLATE EARTH BYPASS F |
| Парткод: | 302H707070 |
| Деталь: | GUIDE BYPASS IN |
| Парткод: | 302H707080 |
| Деталь: | SPRING EARTH BYPASS F |
| Парткод: | 302H707110 |
| Деталь: | COVER MPT BYPASS |
| Парткод: | 302H707120 |
| Деталь: | PUSH COVER BYPASS |
| Парткод: | 302H707130 |
| Деталь: | LABEL JAM BYPASS B2 |
| Парткод: | 302H707140 |
| Деталь: | LABEL JAM BYPASS B3 |
| Парткод: | 302H707150 |
| Деталь: | SPRING BYPASS MOTION |
| Парткод: | 302H707160 |
| Деталь: | PARTS ROLLER BYPASS C |
| Парткод: | 302H794321 |
| Деталь: | PULLEY BYPASS |
| Парткод: | 302KY08020 |
| Деталь: | CUT WASHER |
| Парткод: | 5MVS665KB001 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS MPT BYPASS UNIT SP |
| Парткод: | 302KY94240 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | PRINTED W. BOARD TONER FULL ASSY |
| Парткод: | 302FZ01280 |
| Деталь: | LEVER RETAINER |
| Парткод: | 302FZ02410 |
| Деталь: | SPRING RETAINER |
| Парткод: | 302FZ02420 |
| Деталь: | GEAR SWEEP Z28 |
| Парткод: | 302FZ02850 |
| Деталь: | SHAFT FEED SWEEP |
| Парткод: | 302FZ02860 |
| Деталь: | SPRING JOINT |
| Парткод: | 302FZ31650 |
| Деталь: | PARTS,FAN COOLING DLP 70 SP |
| Парткод: | 302FZ94380 |
| Деталь: | SEAL TONER B |
| Парткод: | 302H703820 |
| Деталь: | HOOK TRAY R |
| Парткод: | 302H702810 |
| Деталь: | HOOK TRAY L |
| Парткод: | 302H702820 |
| Деталь: | SHAFT HOOK |
| Парткод: | 302H702830 |
| Деталь: | HOLDER BOTTLE |
| Парткод: | 302H702840 |
| Деталь: | RETAINER PU |
| Парткод: | 302H703010 |
| Деталь: | HOUSING RETAINER |
| Парткод: | 302H703020 |
| Деталь: | COVER RETAINER |
| Парткод: | 302H703030 |
| Деталь: | PIPE WASTE LOW |
| Парткод: | 302H703040 |
| Деталь: | PIPE WASTE UP |
| Парткод: | 302H703050 |
| Деталь: | SCREW WASTE |
| Парткод: | 302H703060 |
| Деталь: | SHUTTER WASTE |
| Парткод: | 302H703070 |
| Деталь: | SEAL WASTE SHUTTER |
| Парткод: | 302H703080 |
| Деталь: | PIPE DLP LOW |
| Парткод: | 302H703090 |
| Деталь: | SHUTTER PIPE UP |
| Парткод: | 302H703100 |
| Деталь: | SHUTTER PIPE LOW |
| Парткод: | 302H703110 |
| Деталь: | SEAL PIPE DLP LOW |
| Парткод: | 302H703120 |
| Деталь: | SEAL PIPE DLP UP |
| Парткод: | 302H703130 |
| Деталь: | SPRING PIPE LOW |
| Парткод: | 302H703140 |
| Деталь: | ATTACHMENT ID SENSOR |
| Парткод: | 302H703170 |
| Деталь: | ATTACHMENT SW F |
| Парткод: | 302H703180 |
| Деталь: | RAIL WASTE R |
| Парткод: | 302H703190 |
| Деталь: | RAIL WASTE L |
| Парткод: | 302H703200 |
| Деталь: | GEAR WASTE Z24 |
| Парткод: | 302H703210 |
| Деталь: | GEAR SWEEP |
| Парткод: | 302H703221 |
| Деталь: | JOINT WASTE DRIVE |
| Парткод: | 302H703230 |
| Деталь: | SPRING PIPE UP |
| Парткод: | 302H703240 |
| Деталь: | GEAR WASTE Z52S |
| Парткод: | 302H703250 |
| Деталь: | GEAR BEVEL DRIVE Z24 |
| Парткод: | 302H703260 |
| Деталь: | GEAR BEVEL SCREW Z24 |
| Парткод: | 302H703270 |
| Деталь: | SHAFT WASTE DRIVE |
| Парткод: | 302H703280 |
| Деталь: | BRACKET FAN DLP |
| Парткод: | 302H703290 |
| Деталь: | JOINT TUBE |
| Парткод: | 302H703300 |
| Деталь: | JOINT TUBE DLP LID |
| Парткод: | 302H703310 |
| Деталь: | TUBE COOLING LOW K |
| Парткод: | 302H703320 |
| Деталь: | TUBE COOLING LOW Y |
| Парткод: | 302H703330 |
| Деталь: | TUBE COOLING LOW C |
| Парткод: | 302H703340 |
| Деталь: | TUBE COOLING LOW M |
| Парткод: | 302H703350 |
| Деталь: | COVER FULL SENSOR |
| Парткод: | 302H703370 |
| Деталь: | PLATE DRUM EARTH |
| Парткод: | 302H703420 |
| Деталь: | SEAL SCREW |
| Парткод: | 302H703430 |
| Деталь: | LID FULL SENSOR |
| Парткод: | 302H703440 |
| Деталь: | SPRING HOOK WASTE |
| Парткод: | 302H703450 |
| Деталь: | SEAL PIPE WASTE A |
| Парткод: | 302H703460 |
| Деталь: | SEAL FRAME TC B |
| Парткод: | 302FZ21670 |
| Деталь: | SPACER LED /43587J2063 A4 |
| Парткод: | 5MVS313SB002 |
| Деталь: | SPRING WASTE SHUTTER |
| Парткод: | 302H703490 |
| Деталь: | SPRING JOINT TUBE |
| Парткод: | 302H703500 |
| Деталь: | SPRING TRAY WASTE |
| Парткод: | 302H703510 |
| Деталь: | SPRING ATTACHMENT |
| Парткод: | 302H703520 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 302H703530 |
| Деталь: | PIPE DLP UP |
| Парткод: | 302H703540 |
| Деталь: | PLATE HOLDER WT |
| Парткод: | 302H703550 |
| Деталь: | JOINT TUBE DLP BLADE |
| Парткод: | 302H703560 |
| Деталь: | SEAL CONT SHUTTER |
| Парткод: | 302H703570 |
| Деталь: | COVER FILTER |
| Парткод: | 302H703580 |
| Деталь: | FILTER DUST |
| Парткод: | 302H703590 |
| Деталь: | GUIDE CONTAINER M |
| Парткод: | 302H703660 |
| Деталь: | GUIDE CONTAINER C |
| Парткод: | 302H703670 |
| Деталь: | GUIDE CONTAINER Y |
| Парткод: | 302H703680 |
| Деталь: | GUIDE CONTAINER K |
| Парткод: | 302H703690 |
| Деталь: | TUBE COOLING UPPER K |
| Парткод: | 302H703700 |
| Деталь: | TUBE COOLING UPPER M |
| Парткод: | 302H703730 |
| Деталь: | SEAL PIPE WASTE B |
| Парткод: | 302H703740 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H704410 |
| Деталь: | COVER RETAINER LOW |
| Парткод: | 302H704620 |
| Деталь: | Label Cleaning |
| Парткод: | 302H734130 |
| Деталь: | LABEL INNER COVER |
| Парткод: | 302H734161 |
| Деталь: | WIRE RETAINER |
| Парткод: | 302H746050 |
| Деталь: | WIRE TONER SENSOR JOINT |
| Парткод: | 302H746070 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | PARTS RETAINER UNIT |
| Парткод: | 302H793050 |
| Деталь: | PARTS RETANER ASSY |
| Парткод: | 302H794480 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | JOINT DRIVE |
| Парткод: | 302FB06151 |
| Деталь: | PAD MP |
| Парткод: | 302FB17760 |
| Деталь: | SOLENOID LEADING FEED |
| Парткод: | 302FB25180 |
| Деталь: | BASE MPT |
| Парткод: | 302FZ08012 |
| Деталь: | LOWER GUIDE MPT |
| Парткод: | 302FZ08020 |
| Деталь: | SHAFT FEED MPT |
| Парткод: | 302FZ08030 |
| Деталь: | SHAFT FEED JOINT MPT |
| Парткод: | 302FZ08040 |
| Деталь: | SHAFT SEPARATE MPT |
| Парткод: | 302FZ08050 |
| Деталь: | HOLDER MPT LF |
| Парткод: | 302FZ08072 |
| Деталь: | PAPER STOPPER MPT F |
| Парткод: | 302FZ08090 |
| Деталь: | PAPER STOPPER MPT R |
| Парткод: | 302FZ08100 |
| Деталь: | LEVER STOPPER RELEASE |
| Парткод: | 302FZ08110 |
| Деталь: | SPRING SEPARATE PULLEY |
| Парткод: | 302FZ08120 |
| Деталь: | PULLEY LEADING FEED MPT |
| Парткод: | 302FZ08130 |
| Деталь: | HOLDER SEPARATE MPT |
| Парткод: | 302FZ08160 |
| Деталь: | SPRING HOLDER MPT |
| Парткод: | 302FZ08190 |
| Деталь: | SPRING MID MPT |
| Парткод: | 302FZ08291 |
| Деталь: | GEAR MPT Z41Z35 |
| Парткод: | 302FZ08300 |
| Деталь: | ACTUATOR MIDDLE MPT |
| Парткод: | 302FZ08310 |
| Деталь: | LEVER MPT SOLENOID |
| Парткод: | 302FZ08320 |
| Деталь: | SPRING ACTUATOR MPT |
| Парткод: | 302FZ08350 |
| Деталь: | COVER MPT DRIVE |
| Парткод: | 302FZ08360 |
| Деталь: | GEAR JOINT MPT UNIT |
| Парткод: | 302FZ08370 |
| Деталь: | SPRING SOLENOID MPT |
| Парткод: | 302FZ08430 |
| Деталь: | PLATE EARTH MPT ROLL |
| Парткод: | 302FZ08440 |
| Деталь: | SHAFT MIDDLE L |
| Парткод: | 302FZ22140 |
| Деталь: | CLUTCH MPF 6 |
| Парткод: | 302FZ31833 |
| Деталь: | WIRE MPF UNIT |
| Парткод: | 302FZ46520 |
| Деталь: | PARTS,ROLLER MID MPT SP |
| Парткод: | 302FZ94490 |
| Деталь: | TORQUE LIMITER 360 |
| Парткод: | 302GR06110 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | PAD WIRE |
| Парткод: | 302H708130 |
| Деталь: | BUSH SP B |
| Парткод: | 302H722730 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | GEAR MPT FEED Z19 ASSY |
| Парткод: | 302KY08010 |
| Деталь: | GEAR MPT Z23 |
| Парткод: | 302KY08030 |
| Деталь: | FRICTION PLATE,BYPASS |
| Парткод: | 33906400 |
| Деталь: | RING STOPPER 4 |
| Парткод: | 5MVL177DN001 |
| Деталь: | BUSH D1234 |
| Парткод: | 5MVM176XN001 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS MPT ASSY SP |
| Парткод: | 302KY94230 |
| Деталь: | PARTS LSU UNIT HIGH |
| Парткод: | 302KY93160 |
| Деталь: | PIN LSU |
| Парткод: | 302JF19011 |
| Деталь: | SPRING LSU |
| Парткод: | 302FZ20040 |
| Деталь: | PLATE LSU ADJUST |
| Парткод: | 302FZ03061 |
| Деталь: | MOUNT LSU RIGHT |
| Парткод: | 302H702560 |
| Деталь: | PARTS MC ASSY |
| Парткод: | 302KY93170 |
| Деталь: | PARTS DRUM 50 M UNIT |
| Парткод: | 302KY93070 |
| Деталь: | PARTS PWB HVU CONTROL ASSY SP |
| Парткод: | 302H794080 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | RETAINING PIN DRAWER |
| Парткод: | 302FZ03070 |
| Деталь: | MOTOR LIFT |
| Парткод: | 302GR44112 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | SEAL TONER A |
| Парткод: | 302H703850 |
| Деталь: | GUIDE HARNESS |
| Парткод: | 302H703760 |
| Деталь: | FELT TC CLN |
| Парткод: | 2BG16590 |
| Деталь: | SHUTTER ID SENSOR |
| Парткод: | 302FZ02190 |
| Деталь: | SPRING SHUTTER ID SENSOR |
| Парткод: | 302FZ02200 |
| Деталь: | PLATE ID SENSOR |
| Парткод: | 302FZ02771 |
| Деталь: | RAIL DRUM LEFT |
| Парткод: | 302H702170 |
| Деталь: | SHEET TRANSFER R |
| Парткод: | 302H702432 |
| Деталь: | GUIDE TC R |
| Парткод: | 302H702441 |
| Деталь: | SPRING EARTH ICL |
| Парткод: | 302H702500 |
| Деталь: | LOWER FILM ID SENSOR |
| Парткод: | 302H733260 |
| Деталь: | FRONT FILM ID SENSOR |
| Парткод: | 302H733290 |
| Деталь: | WIRE REG SENS |
| Парткод: | 302H746350 |
| Деталь: | PARTS ID SENSOR |
| Парткод: | 302H794220 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | GUIDE WIRE VU |
| Парткод: | 302H739250 |
| Деталь: | WIRE MPF/HVU |
| Парткод: | 302H746210 |
| Деталь: | WIRE LIFT MOT |
| Парткод: | 302H746570 |
| Деталь: | CAP CAS FOOT |
| Парткод: | 302H702950 |
| Деталь: | SPRING ICL |
| Парткод: | 302H739530 |
| Деталь: | TERMINAL ICL |
| Парткод: | 302H739580 |
| Деталь: | WIRE CLEANING |
| Парткод: | 302H746320 |
| Деталь: | HOLDER HV2 TC |
| Парткод: | 302FZ39610 |
| Деталь: | SPRING HV2 TC |
| Парткод: | 302FZ39620 |
| Деталь: | SPRING HV2 SE |
| Парткод: | 302FZ39630 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 302H045080 |
| Деталь: | COVER INNER LEFT |
| Парткод: | 302H704210 |
| Деталь: | SHEET INNER LEFT |
| Парткод: | 302H704650 |
| Деталь: | WIRE HVU T2 |
| Парткод: | 302H746120 |
| Деталь: | PARTS HVU HIGH VOLTAGE TRANSFER 2 SP |
| Парткод: | 302KA94080 |
| Деталь: | COVER CONN |
| Парткод: | 302GR39190 |
| Деталь: | BRACKET PPT |
| Парткод: | 302H702240 |
| Деталь: | MOUNT CASSETTE SW |
| Парткод: | 302FZ02610 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | PLATE EARTH PWB |
| Парткод: | 302H702580 |
| Деталь: | PARTS PWB FRONT MAIN ASSY SP |
| Парткод: | 302H794130 |
| Деталь: | PARTS PWB FRONT SUB ASSY SP |
| Парткод: | 302H794140 |
| Деталь: | COVER CONNECTOR HEATER |
| Парткод: | 302H702670 |
| Деталь: | WIRE EJECT JOINT |
| Парткод: | 302KA46020 |
| Деталь: | COVER INLET |
| Парткод: | 302H739060 |
| Деталь: | SHEET COVER INLET |
| Парткод: | 302H739630 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | HOLDER MOTOR ICL |
| Парткод: | 302H703620 |
| Деталь: | PARTS DC MOTOR ASSY |
| Парткод: | 302H794440 |
| Деталь: | GEAR WORM /48390M0062 A4 |
| Парткод: | 5MVG115DB002 |
| Деталь: | LABEL L,HIGH TEMPERATURE CAUTION(EXP) |
| Парткод: | 20305130 |
| Деталь: | BASE HEATER OP |
| Парткод: | 302H702210 |
| Деталь: | PARTS HEATER DEHUMIDIFIER 240 |
| Парткод: | 302H794610 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | SHEET RAIL IMAGE |
| Парткод: | 302H702180 |
| Деталь: | PARTS ID SENSOR UNIT |
| Парткод: | 302H794392 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | PIN CURSOR |
| Парткод: | 2FB07050 |
| Деталь: | SPRING CURSOR |
| Парткод: | 2FB07060 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT, WORK PLATE |
| Парткод: | 302AR07041 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 302BC07861 |
| Деталь: | PLATE SIZE C |
| Парткод: | 302FB05200 |
| Деталь: | LEVER CURSOR A |
| Парткод: | 302FB07032 |
| Деталь: | LEVER CURSOR B |
| Парткод: | 302FB07042 |
| Деталь: | PIN CASSETTE |
| Парткод: | 302FB07420 |
| Деталь: | LEVER CASSETTE |
| Парткод: | 302GR09051 |
| Деталь: | SPRING LEVER CASSETTE |
| Парткод: | 302GR09120 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 302GR09130 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302GR09140 |
| Деталь: | WORK PLATE HANDLE |
| Парткод: | 302GR09150 |
| Деталь: | PLATE SIZE INCH |
| Парткод: | 302GR09201 |
| Деталь: | SEAL DETECTION PLATE |
| Парткод: | 302GR09210 |
| Деталь: | FILM PWB COVER |
| Парткод: | 302GR09250 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | WIRE CASSETTE UNIT |
| Парткод: | 302GR46450 |
| Деталь: | WORK PLATE LIFT CASSETTE |
| Парткод: | 302H009070 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302H009101 |
| Деталь: | CURSOR C CASSETTE |
| Парткод: | 302H009110 |
| Деталь: | PLATE CASSETTE EARTH |
| Парткод: | 302H009120 |
| Деталь: | LABEL PAPER SET |
| Парткод: | 302H034070 |
| Деталь: | COVER CASSETTE 2ND |
| Парткод: | 302H709021 |
| Деталь: | COVER CASSETTE HANDLE |
| Парткод: | 302H709030 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302H709040 |
| Деталь: | CASSETTE 2ND |
| Парткод: | 302H709060 |
| Деталь: | JOINT HANDLE CASSETTE |
| Парткод: | 302H709070 |
| Деталь: | ADJUSTING PLATE CASSETTE |
| Парткод: | 302H709080 |
| Деталь: | FRONT CURSOR CASSETTE |
| Парткод: | 302H709090 |
| Деталь: | REAR CURSOR CASSETTE |
| Парткод: | 302H709100 |
| Деталь: | RAIL CURSOR R |
| Парткод: | 302H709110 |
| Деталь: | LID PAPER SIZE |
| Парткод: | 302H709120 |
| Деталь: | RAIL CURSOR A |
| Парткод: | 302H709130 |
| Деталь: | Support Plate |
| Парткод: | 302H709140 |
| Деталь: | DETECTION PLATE PAPER SIZE |
| Парткод: | 302H709150 |
| Деталь: | SPRING PAD |
| Парткод: | 302H709190 |
| Деталь: | LABEL CASSETTE SIZE L |
| Парткод: | 302H734050 |
| Деталь: | LABEL CASSETTE SIZE S |
| Парткод: | 302H734060 |
| Деталь: | LABEL CASSETTE OPERATION B |
| Парткод: | 302H734070 |
| Деталь: | LABEL PAPER UPPER LIMIT |
| Парткод: | 302H734080 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302KY09010 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | PLATE NUMBER4 |
| Парткод: | 3CF04060 |
| Деталь: | PARTS TOP CASSETTE 2 ASSY |
| Парткод: | 302H793311 |
Коды ошибок
C0100
C0120
C0150
C0160
C0170
C0180
C0320
C0640
C0800
C0840
C1010
C1020
C1030
C1040
C1100
C1110
C1120
C1130
C1800
C1900
C1950
C2101
C2102
C2201
C2202
C2203
C2204
C2211
C2212
C2213
C2214
C2231
C2232
C2233
C2234
C2241
C2242
C2243
C2244
C2261
C2262
C2263
C2264
C2271
C2272
C2273
C2274
C2300
C2351
C2352
C2400
C2500
C2550
C2600
C2700
C2810
C2950
C4000
C4010
C4100
C4200
C5101
C5102
C5103
C5104
C5301
C5302
C5303
C5304
C6000
C6010
C6020
C6030
C6040
C6050
C6100
C6120
C6130
C6150
C6200
C6220
C6230
C6400
C6410
C7000
C7100
C7101
C7102
C7103
C7104
C7200
C7210
C7240
C7250
C7401
C7402
C7403
C7404
C7411
C7412
C7413
C7414
C7420
C7601
C7602
C7800
C7901
C7902
C7903
C7904
C7911
C7912
C7913
C7914
C7950
C8020
C8030
C8040
C8050
C8060
C8070
C8140
C8170
C8180
C8210
C8220
C8230
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8440
C8460
C8500
C8510
C8800
C8900
C8910
C8920
C8930
C9530 ... C9550
F000
F020
F040
F050
F278
Описание
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0120 |
| Description: | MAC address data error |
| Causes: | The MAC address data is incorrect. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0320 |
| Description: | Power CPU communication problem A communication error is detected 10 times in succession. |
| Causes: | Defective engine PWB. |
| Remedy: | Replace the engine PWB and check for correct operation. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0840 |
| Description: | RTC error ("Time for maintenance T" appears) |
| Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
| Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1100 |
| Description: | PF lift motor 1 error |
| Causes: | [The right cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because one of the phenomena below. 1. PF lift sensor 1 does not turn on when passing 23s while PF lift motor 1 turns on for the first time after inserting the cassette. 2. PF lift sensor 1 does not turn on when passing 2s while PF lift motor 1 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 1 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 1 - PF main PWB Wiring diagram 4 Checking PF lift motor 1 PF lift motor 1 is faulty. Replace PF lift motor 1. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift sensor 1 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 1 is not properly attached or faulty. Reattach PF lift sensor 1. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1120 |
| Description: | PF left lift position problem (optional 3000-sheet paper feeder) Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 1. Defective PF lift motor 2. The PF left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 1. Check if YC5-4 on the PF main PWB goes low when level switch 1 is turned off. If not, replace PF lift switch 1. Defective PF lift motor 1. Check for continuity across the coil. If none, replace PF lift motor 1. The PF left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1800 |
| Description: | Large capacity feeder communication error Condition: When turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error does not reappear. (It is caused by the large capacity feeder.) |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1900 |
| Description: | Large capacity feeder EEPROM error Condition: When outputting Event Log after turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error is not recorded. (It is caused by the large capacity feeder.) (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1950 |
| Description: | Primary transfer belt unit EEPROM error |
| Causes: | The EEPROM cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data do not match 8 times continuously. |
| Remedy: | 1 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed or the connector is not connected. Reinstall the primary transfer belt unit and reconnect the connector. Detaching and reattaching the primary transfer belt unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 3 Primary transfer belt unit replacement The primary transfer belt unit is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2102 |
| Description: | Developer motor C error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor C drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor C is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking developer motor C The developer motor C drive is faulty. Execute U030 [DLP(C)] and check the developer motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 5 Checking developer motor C Developer motor C is not properly attached or faulty. Reattach developer motor C. If not repaired, replace the motor. Detaching and reattaching the main drive unit 6 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2201 |
| Description: | Drum motor steady-state error |
| Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
| Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2202 |
| Description: | Drum motor C steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB C at every 1s. |
| Remedy: | 1 Checking drum motor C The drum motor C drive is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2203 |
| Description: | Drum motor M steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB M at every 1s. |
| Remedy: | 1 Checking drum motor M The drum motor M drive is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2204 |
| Description: | Drum motor Y steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB Y at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y drive is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2211 |
| Description: | Drum motor startup error |
| Causes: | The ready signal does not turn on when passing 2s after the drum motor starts up. |
| Remedy: | 1 Checking the drum motor The drum motor operation is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2212 |
| Description: | Drum motor M startup error |
| Causes: | When reading the signal from encoder PWB C at every 1s, it does not become stable when passing 5s after the drum motor M starts driving. |
| Remedy: | 1 Checking drum motor M The drum motor M operation is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2213 |
| Description: | Drum motor M startup error Drum motor M is not stabilized within 5 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drum motor M. Defective PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the motor control PWB and the connector of the drum motor M, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum motor M. Replace the drum motor M. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C2214 |
| Description: | Drum motor Y startup error |
| Causes: | When reading the signal from encoder PWB C at every 1s, it does not become stable when passing 5s after the drum motor Y starts driving. |
| Remedy: | 1 Checking drum motor Y The drum motor Y operation is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB.| 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2231 |
| Description: | Drum motor main sensor K startup error |
| Causes: | The main pulse abnormal stop is detected when reading the signal from encoder PWB K (1) at every 1s. |
| Remedy: | 1 Checking drum motor K The drum motor K operation is faulty. Execute U030 [Process] and check the drum motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB K - Drum motor K • Drum motor K - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB K is faulty. Replace drum drive unit K. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2232 |
| Description: | Drum motor main sensor C startup error |
| Causes: | The main pulse abnormal stop is detected when reading the signal from encoder PWB C (1) at every 1s. |
| Remedy: | 1 Checking drum motor C The drum motor C operation is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB C - Drum motor C • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB C is faulty. Replace drum drive unit C. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2233 |
| Description: | Drum motor main sensor M startup error |
| Causes: | The main pulse abnormal stop is detected when reading the signal from encoder PWB Y (1) at every 1s. |
| Remedy: | 1 Checking drum motor M The drum motor M operation is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB M - Drum motor M • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB M is faulty. Replace drum drive unit M. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2234 |
| Description: | Drum motor main sensor Y startup error |
| Causes: | The main pulse abnormal stop is detected when reading the signal from encoder PWB Y (1)at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y operation is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB Y - Drum motor Y • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB Y is faulty. Replace drum drive unit Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2241 |
| Description: | Drum motor sub sensor K startup error (For the internal count) |
| Causes: | The FG abnormal stop is detected when reading the signal from encoder PWB K (2) at every 1s. |
| Remedy: | 1 Checking drum motor K The drum motor K operation is faulty. Execute U030 [Process] and check the drum motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB K - Drum motor K • Drum motor K - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB K is faulty. Replace drum drive unit K. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2242 |
| Description: | Drum motor sub sensor C startup error (For the internal count) |
| Causes: | The FG abnormal stop is detected when reading the signal from encoder PWB C (2) at every 1s. |
| Remedy: | 1 Checking drum motor C The drum motor C operation is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB C - Drum motor C • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB C is faulty. Replace drum drive unit C. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2243 |
| Description: | Drum motor sub sensor M startup error (For the internal count) |
| Causes: | The FG abnormal stop is detected when reading the signal from encoder PWB Y (2) at every 1s. |
| Remedy: | 1 Checking drum motor M The drum motor M operation is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB M - Drum motor M • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB M is faulty. Replace drum drive unit M. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2244 |
| Description: | Drum motor sub sensor Y startup error (For the internal count) |
| Causes: | The FG abnormal stop is detected when reading the signal from encoder PWB Y (2) at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y operation is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Encoder PWB Y - Drum motor Y • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 4 Replacing the drum drive unit Encoder PWB Y is faulty. Replace drum drive unit Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2261 |
| Description: | Drum motor K device sensor error The device alarm signal is input. |
| Causes: | Poor contact in the connector terminals Defective drum motor K. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC8 on the motor control PWB and the connector of the drum motor K, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum motor K. Replace the drum motor K. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C2262 |
| Description: | Drum motor C device error The device alarm signal is input. |
| Causes: | Poor contact in the connector terminals. Defective drum motor C. Defective PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the motor control PWB and the connector of the drum motor C, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum motor C. Replace the drum motor C. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C2263 |
| Description: | Drum motor M device error The device alarm signal is input. |
| Causes: | Poor contact in the connector terminals. Defective drum motor M. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the motor control PWB and the connector of the drum motor M, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum motor M. Replace the drum motor M. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C2264 |
| Description: | Drum motor Y device error The device alarm signal is input. |
| Causes: | Poor contact in the connector terminals. Defective drum motor Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC7 on the motor control PWB and the connector of the drum motor Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum motor Y. Replace the drum motor Y. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C2271 |
| Description: | Drum position sensor K error While the drum rotates two turns, no signal is input to the sensor. |
| Causes: | Poor contact in the connector terminals. Defective drum position sensor K. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main front PWB and the connector of the drum unit K, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum position sensor K. Replace the drum unit K. Defective PWB. Replace the main front PWB or engine PWB and check for correct operation. |
| Error code: | C2272 |
| Description: | Drum position sensor C error While the drum rotates two turns, no signal is input to the sensor. |
| Causes: | Poor contact in the connector terminals. Defective drum position sensor C. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the sub front PWB and the connector of the drum unit C, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum position sensor C. Replace the drum unit C. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C2273 |
| Description: | Drum position sensor M error While the drum rotates two turns, no signal is input to the sensor. |
| Causes: | Poor contact in the connector terminals. Defective drum position sensor M. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC7 on the sub front PWB and the connector of the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum position sensor M. Replace the drum unit M. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C2274 |
| Description: | Drum position sensor Y error While the drum rotates two turns, no signal is input to the sensor. |
| Causes: | Poor contact in the connector terminals. Defective drum position sensor Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective drum position sensor Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C2300 |
| Description: | Fuser motor error |
| Causes: | 1. The ready signal is at the H level for 1s continuously during the fuser motor drive. 2. The ready signal is not at the L level (stable rotation) when passing 2s after the fuser motor drive starts. |
| Remedy: | 1 Checking the fuser motor The fuser motor operation is faulty. Execute U030 [Fuser] and check the fuser motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Fuser motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Replacing the fuser motor The fuser motor is faulty. Replace the fuser motor. Detaching and reattaching the fuser drive unit 5 Replacing the fuser drive unit The fuser drive unit is faulty. Replace the fuser drive unit. Detaching and reattaching the fuser drive unit 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2351 |
| Description: | Cleaning motor K error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective cleaning motor K. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC16 on the engine PWB and the connector of the cleaning motor K, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective cleaning motor K. Run maintenance item U030 and check if the cleaning motor K operates when YC16- B13 (remote signal) on the engine PWB goes low. If not, replace the cleaning motor K. Defective engine PWB. Run maintenance item U030 and check if YC16-B13 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
| Error code: | C2352 |
| Description: | Cleaning motor MCY error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective cleaning motor K. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC16 on the engine PWB and the connector of the cleaning motor MCY, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective cleaning motor K. Run maintenance item U030 and check if the cleaning motor MCY operates when YC16-A13 (remote signal) on the engine PWB goes low. If not, replace the cleaning motor MCY. Defective engine PWB. Run maintenance item U030 and check if YC16-A13 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
| Error code: | C2400 |
| Description: | Eject motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective eject motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC25 on the engine PWB and the connector on the eject motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective eject motor. Run maintenance item U030 and check if the eject motor operates when YC25-A5 (remote signal) on the engine PWB goes low. If not, replace the eject motor. Defective engine PWB. Run maintenance item U030 and check if YC25-A5 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2550 |
| Description: | Transfer motor error |
| Causes: | 1. The ready signal is not at the L level (stable rotation) when passing 2s after the transfer motor drive starts. 2. The ready signal is at the H level for 1s continuously during the transfer motor drive. |
| Remedy: | 1 Checking the transfer motor The transfer motor operation is faulty. Check if the transfer belt and the drive gears rotate smoothly or have no excessive load. Apply grease to the frictional parts and repair the parts. 2 Checking the conveying unit The drawer connector connection between the conveying unit and the main unit is faulty. Firmly close the conveying unit. If there are foreign objects or the deformation on the drawer connector of the conveying unit for connecting to the main unit, repair them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Transfer motor - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB 4 Replacing the transfer motor The transfer motor is faulty. Replace the transfer motor. 5 Replacing the transfer belt unit The transfer belt unit is faulty. Replace the transfer belt unit. Detaching and reattaching the transfer belt unit 6 Replacing the relay PWB The relay PWB is faulty. Replace the relay PWB. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C2700 |
| Description: | Color release motor error |
| Causes: | Turning the color release sensor on and off is not detected for 5s while the color release motor is driving. |
| Remedy: | 1 Checking the drive components The drive transmission from the color release motor error is faulty. Execute U030 [CMY Release]. If the drive from the motor is not transmitted, repair the drive parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 5 Primary transfer belt unit replacement The primary transfer roller lift-up drive section is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2810 |
| Description: | Waste toner motor error |
| Causes: | The steady-state speed error, FG pulse abnormal stop, or the abnormal motor drive is detected when reading the error signal from the motor at every 1s. |
| Remedy: | 1 Checking the waste toner box The waste toner box is not properly installed. Reinstall the waste toner box. Detaching and reattaching the waste toner box 2 Checking the waste toner motor The waste toner motor does not operate properly. Check if the waste toner motor has no excessive load, and repair it. 3 Checking the drive gear The drive gear does not rotate properly. Check if the excessive load is not applied to the drive gears by rotating the gears, and clean the drive gears and the bushing, etc. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Waste toner motor - Front PWB?• Front PWB - Engine PWB Wiring diagram 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2950 |
| Description: | Motor control PWB communication error A communication error from motor control PWB is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 and YC15 on the engine PWB and the connector of the motor control PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the motor control PWB or engine PWB and check for correct operation. |
| Error code: | C4000 |
| Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4010 |
| Description: | Polygon motor steady-state problem • The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4100 |
| Description: | Exposure lamp stays on |
| Causes: | Defective laser scanner unit. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser scanner unit. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB. Repair or replace if necessary. |
| Error code: | C4200 |
| Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
| Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C5101 |
| Description: | Main high-voltage error |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the high-voltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Repair the main charger roller contact (wire spring) inside the high-voltage PWB so that it firmly contacts. Detaching and reattaching the high-voltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw does not properly rotate due to the excessive load. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity.• High-voltage PWB - Engine PWB Wiring diagram 7 Replacing the high-voltage PWB The high-voltage PWB is faulty. Replace the high-voltage PWB. Detaching and reattaching the high-voltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5104 |
| Description: | Main high-voltage error Y |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5301 |
| Description: | Cleaning lamp K error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp K. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main front PWB and the connector of the drum unit K, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp K. Replace the drum unit K. Defective PWB. Replace the main front PWB or engine PWB and check for correct operation. |
| Error code: | C5302 |
| Description: | Cleaning lamp C error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp C. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the sub front PWB and the connector of the drum unit C, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp C. Replace the drum unit C. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5303 |
| Description: | Cleaning lamp M error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp M. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC7 on the sub front PWB and the connector of the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp M. Replace the drum unit M. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5304 |
| Description: | Cleaning lamp Y error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6010 |
| Description: | Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more. |
| Causes: | Defective PWB. |
| Remedy: | Replace the power source PWB or engine PWB and check for correct operation. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6040 |
| Description: | Fuser heater error |
| Causes: | The fuser center thermistor outputs the abnormal value for 1s continuously. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6100 |
| Description: | Fuser heater broken (For the internal count) |
| Causes: | The fuser press thermistor temperature detected does not reach the control temperature within 480s after shifting to the low power mode. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6120 |
| Description: | Fuser press thermistor high temperature error |
| Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6130 |
| Description: | Fuser press thermistor broken |
| Causes: | The detection temperature of the fuser press thermistor does not reach 30°C / 86°F within 60s since warm-up starts. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6150 |
| Description: | Fuser press thermistor low temperature error |
| Causes: | The fuser press thermistor detects less than 30°C / 86°F for 1s after warm-up. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6200 |
| Description: | Fuser IH ends heating error |
| Causes: | The temperature detected at the fuser edge thermistor does not reach 100°C / 212°F within 60s since warmup starts. The temperature detected at the fuser edge thermistor does not reach the ready display temperature within 60s since it reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. 6 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. Executing U030 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 11 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 12 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6220 |
| Description: | Fuser edge thermistor high temperature error |
| Causes: | The fuser edge thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 8 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the fuser edge fan motor Dust accumulates on the fuser edge fan motor, or the motor is not properly attached. Clean the front / rear fuser edge fan motors and reattach them. Fan Motors Attachable Direction |
| Error code: | C6230 |
| Description: | Fuser edge thermistor broken |
| Causes: | The fuser edge thermistor detects 37°C / 98°or less for 1s when the fuser center thermistor detects 100°C / 212°F or more for 1s during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 11 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6410 |
| Description: | Fuser unit type mismatch error |
| Causes: | "Unit Identification" code in the EEPROM of the fuser unit does not match the main unit. The fuser unit for other model is installed. |
| Remedy: | 1 Replacing the fuser unit The fuser unit for other models is installed. Install the fuser unit for the applicable models. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 5 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7000 |
| Description: | Toner motor problem After driving of the toner motor starts, the error signal is not at the H level for 500 ms continuously. |
| Causes: | Poor contact in the connector terminals. Broken the gear Defective toner motor M/C/Y/K. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC26 on the engine PWB and the connector of the toner motor, and the continuity across the connector terminals. Repair or replace if necessary. Broken the gear. Check visually and replace the gear if necessary. Defective toner motor M/C/Y/K. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C7100 |
| Description: | Toner container motor error The rated speed achievement signal does not turn to L within 2 s since toner container motor is activated. The rated speed achievement signal is at the H level for 1 s continuously after toner container motor is stabilized. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective toner container motor Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC26 on the engine PWB and the connector on the toner container motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective toner container motor. Run maintenance item U030 and check if the toner container motor operates when YC26-A7 (remote signal) on the engine PWB goes low. If not, replace the toner container motor. Defective engine PWB. Run maintenance item U030 and check if YC26-A7 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
| Error code: | C7101 |
| Description: | Toner sensor error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7102 |
| Description: | Toner sensor C error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7103 |
| Description: | Toner sensor M error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7104 |
| Description: | Toner sensor Y error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7200 |
| Description: | Internal thermistor broken (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7210 |
| Description: | Internal thermistor short-circuited (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) is less than the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7240 |
| Description: | Broken internal thermistor 2 wire An abnormal value is detected in the input data to inner temperature sensor 2. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C7250 |
| Description: | Short-circuited internal thermistor 2 An abnormal value is detected in the input data to inner temperature sensor 2. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C7401 |
| Description: | Developer unit type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit does not match the main unit. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7402 |
| Description: | Developer unit C type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit C does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7403 |
| Description: | Developer unit M type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit M does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7404 |
| Description: | Developer unit Y type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit Y does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7411 |
| Description: | Drum unit type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit does not match the main unit. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7412 |
| Description: | Drum unit C type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit C does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7413 |
| Description: | Drum unit M type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit M does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7414 |
| Description: | Drum unit Y type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit Y does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7420 |
| Description: | Uninstalled primary transfer unit |
| Causes: | 1. Unit identification code does not match. 2. Unit for the other model is installed. |
| Remedy: | 1 Replacing the primary transfer unit The primary transfer unit for other models is installed. Install the primary transfer unit for the applicable models. Detaching and reattaching the Primary Transfer Unit 2 Reinstalling the primary transfer unit The connector of the primary transfer unit is not firmly connected. Reinstall the primary transfer unit so that the connector firmly connects. Detaching and reattaching the Primary Transfer Unit 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer connect PWB - Feed image PWB Service Manual - Section 8 `PWBs` 4 Firmware upgrade The firmware is faulty. Reinstall the engine firmware. Firmware Update 5 Replacing the transfer connection PWB The transfer connection PWB is faulty. Replace the transfer connection PWB. 6 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
| Error code: | C7601 |
| Description: | Front ID sensor error (For the internal count) |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the front ID sensor The front ID sensor is dirty. Clean the front ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not properly operate, reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid. 5 Checking the front ID sensor The front ID sensor is not properly attached. Reattach the front ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Front ID sensor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 7 Replacing the front D sensor The front ID sensor is faulty. Check if the value of U465 [T7 CTD] is fluctuated before and after Calibration, and replace the front ID sensor if it was not fluctuated (uncalibrated) . Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7602 |
| Description: | ID sensor error |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the ID sensor The ID sensor is dirty. Clean the ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. If the ID sensor shutter does not operate properly when executing U033 [ID Sensor] , reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid 5 Checking the ID sensor The ID sensor is not properly attached. Reattach the ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • ID sensor - Feed PWB 7 Replacing the ID sensor The ID sensor is faulty. Check if the value of "T7 CTD" at U465 fluctuates before and after executing Calibration. If not (no adjustment), replace the ID sensor. Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7901 |
| Description: | Drum unit EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7902 |
| Description: | Drum unit C EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7903 |
| Description: | Drum unit M EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7904 |
| Description: | Drum unit Y EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7911 |
| Description: | Developer unit EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7912 |
| Description: | Developer unit C EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit C cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit C - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7913 |
| Description: | Developer unit M EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit M cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7914 |
| Description: | Developer unit Y EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit Y cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7950 |
| Description: | High voltage control PWB error A communication error from high voltage control PWB is detected 10 times in succession |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC30 on the engine PWB and the connector on the high voltage control PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the high voltage control PWB or engine PWB and check for correct operation. |
| Error code: | C8020 |
| Description: | Punch motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position is not aligned within 3s when initializing the home position or standby. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8040 |
| Description: | Document finisher lower paper conveying belt problem • During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position. JAM87 is indicated the first time this problem occurs. If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt. • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s. |
| Causes: | Phase shift of the lower paper conveying belt. Malfunction of the lower paper conveying belt motor. Malfunction of the lower paper conveying belt home position sensor. Loose connection of the lower paper conveying belt home position sensor connector. Incorrect insertion of the intermediate tray. Defective finisher main PWB. |
| Remedy: | Phase shift of the lower paper conveying belt. Correct the phase of the lower paper conveying belt and check for correct operation. Malfunction of the lower paper conveying belt motor. Replace the lower paper conveying belt motor and check for correct operation. Malfunction of the lower paper conveying belt home position sensor. Replace the lower paper conveying belt home position sensor and check for correct operation. Loose connection of the lower paper conveying belt home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Incorrect insertion of the intermediate tray. Check whether the intermediate tray catches are damaged. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8050 |
| Description: | Punch shift motor error 2 Object: 100-sheet staple finisher |
| Causes: | The paper edge cannot be detected if driving the motor by the specified distance (30mm) when detecting the paper edge. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit does not move manually, repair the position where restricts the operation. 2 Checking the PH cam drive parts The PH cam drive parts are not attached properly or faulty. Reattach the punch cam drive components. Replace it if not repaired 3 Checking the connection The connector is not properly connected. Or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EPunch shift motor - PH PWB EPaper edge sensor 1,2 - PH PWB EPH PWB- DF PWB 4 Replacing the punch shift motor The punch shift motor is faulty. Execute U240 mMotorn > mPunch Moven Replace the punch shift motor if it does not operate properly. 5 Checking the paper edge sensors 1, 2 Paper edge sensors 1, 2 are not properly attached or faulty. Execute U241 mPunchn > mEdge Face1/2n Reattach the paper edge sensors 1, 2 if they do not operate properly. Replace the paper edge sensors 1, 2 if not repaired. 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. 7 Replacing PH PWB PH PWB is faulty. Replace PH PWB. 8 Replacing DF PWB DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. |
| Error code: | C8060 |
| Description: | Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1.5 s. Paper conveying belt home position sensor 2 does not turn on within 1.5 s. |
| Causes: | Poor contact in the connector terminals. Defective paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Defective PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the inner tray PWB and the connector on paper conveying belt motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper conveying belt home position sensor 2. Replace paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Replace paper conveying belt motor 2. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
| Error code: | C8070 |
| Description: | Inner tray communication error (optional 3000-sheet document finisher) Communication with the inner tray is not possible although the connection is detected. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 and YC24 on the finisher main PWB and the connector YC1 and YC4 on the inner tray PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8220 |
| Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8230 |
| Description: | DF staple motor error Object: 4000-sheet finisher |
| Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8300 |
| Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
| Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8310 |
| Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8320 |
| Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
| Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8330 |
| Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
| Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8340 |
| Description: | BF staple motor error 1 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8350 |
| Description: | BF side registration motor 1 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 1 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the lower BF side registration guide The lower BF side registration guide is not assembled properly. If the lower BF side registration guide is not operated manually, repair the part that restricts the operation. 2 Checking the lower BF side registration guide drive components The lower BF side registration guide drive parts are not properly attached or faulty. Reattach the lower BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 1 - BF main PWB • BF side registration sensor 1 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 1 BF side registration motor 1 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 1 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 1 BF side registration sensor 1 is not properly attached or faulty. Reattach BF side registration sensor 1 and execute U241 [Booklet] > [Width Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8360 |
| Description: | BF main motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The lock-up signal was detected for 1s continuously during the motor operation. |
| Remedy: | 1 Checking the BF conveying roller The BF conveying roller is not assembled properly. If the BF conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the BF conveying roller drive parts The BF conveying roller drive parts are not properly attached or faulty. Reattach the BF conveying roller drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main motor - BF main PWB Wiring diagram 4 Replacing the BF main motor The BF main motor is faulty. Execute U240 [Booklet] > [Folding]. If the BF main motor does not properly operate, replace it. Executing U240 5 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8460 |
| Description: | EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or finisher main PWB. |
| Remedy: | Replace the finisher main PWB and check for correct operation. |
| Error code: | C8500 |
| Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
| Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8510 |
| Description: | MB conveying motor error 1 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn on after passing 5s during the initial operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB Wiring diagram 3 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. 4 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8800 |
| Description: | Main program error (DF) / Engine - DF communication error Object: 4000-sheet finisher |
| Causes: | The main program is faulty when turning on the power. The Engine -DF communication error is detected 10 times continuously. |
| Remedy: | 1 Resetting the main power The program does not start up properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8900 |
| Description: | DF backup error Object: 4000-sheet finisher (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 2 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8910 |
| Description: | Backup memory data problem (optional of 3000-sheet document finisher) Read and write data does not match 3 times in succession. |
| Causes: | Poor contact in the connector terminals Defective punch PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the punch PWB and the connector YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective punch PWB. Replace the punch PWB and check for correct operation. |
| Error code: | C8920 |
| Description: | Mailbox backup problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match. |
| Causes: | Poor contact in the connector terminals. Defective mailbox main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the mailbox main PWB and the connector YC7 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective mailbox main PWB. Replace the mailbox main PWB and check for correct operation. |
| Error code: | C8930 |
| Description: | BF unit backup error Object: 4000-sheet finisher + Folding unit (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 2 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C9530 ... C9550 |
| Description: | Contact the Service Administrative Division. |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F278 |
| Description: | Secondary power source error |
| Causes: | The operation became unstable since the primary supply power dropped out temporarily and recovered. |
| Remedy: | 1 Resetting the main power The power reset was performed immediately. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the LVU and reinsert the wire connectors. If there is no continuity, replace the wire. 3 Replacing the LVU The LVU is faulty. Replace the LVU. |
Парткод
Название
Kyocera Блок фотобарабана
Kyocera Блок проявки голубой
Kyocera Блок проявки черный
Kyocera Блок проявки пурпурный
Kyocera Блок проявки желтый
Kyocera Узел термозакрепления 230v
Kyocera Сервисный комплект цветной
Kyocera Сервисный комплект черный
(MK-856B) Kyocera Сервисный комплект цветной
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый
